Related Experiment Video

Updated: Jul 26, 2026

Perturbing Endothelial Biomechanics via Connexin 43 Structural Disruption
09:20

Perturbing Endothelial Biomechanics via Connexin 43 Structural Disruption

Published on: October 4, 2019

Membrane stress and torque induced by Frank's nematic textures: A geometric perspective using surface-based

J A Santiago1,2, G Chacón-Acosta1, F Monroy2,3

  • 1Departamento de Matemáticas Aplicadas y Sistemas, Universidad Autónoma Metropolitana Cuajimalpa, Vasco de Quiroga 4871, 05348 Ciudad de México, Mexico.

Physical Review. E
|September 11, 2019
PubMed

More Related Videos

Fabrication and Implementation of a Reference-Free Traction Force Microscopy Platform08:10

Fabrication and Implementation of a Reference-Free Traction Force Microscopy Platform

Published on: October 6, 2019

Direct Force Measurements of Subcellular Mechanics in Confinement using Optical Tweezers09:56

Direct Force Measurements of Subcellular Mechanics in Confinement using Optical Tweezers

Published on: August 31, 2021

Related Concept Videos

Stress on an Oblique Plane01:16

Stress on an Oblique Plane

Understanding stress on an oblique plane under axial loading is pivotal in material mechanics. This analysis offers insight into a material's durability and strength, which is crucial for civil engineering and structural design. Axial loading refers to force application along the material's central axis, causing compression or elongation and leading to normal stress. Normal stress occurs when a force acts perpendicularly to the material's area, resulting in compressive or tensile stress. When...
Stress: General Loading Conditions01:15

Stress: General Loading Conditions

To grasp the intricacy of real-world conditions where multiple loads are applied simultaneously to a structure, one might visualize a section passing through a specific point within a body, aligned parallel to the xy plane. This section is subjected to various forces, including original loads, normal forces, and shearing forces.
The shearing force, possessing potential directionality within the plane of the section, is simplified into two component forces running parallel to the x and y axes.
Components of Stress01:23

Components of Stress

Stress analysis under multiple loading conditions is intricate, necessitating a comprehensive grasp of normal and shearing stresses. Consider a small cube at point O, subjected to stress on all six faces, visible or not. Normal stress components σx, σy, σz act perpendicularly to the x, y, and z axes. Shearing stress components τxy and τxz are exerted on faces perpendicular to these axes.
Interestingly, the hidden cube faces also experience these stresses, equal and opposite to those on the...
Stress Concentrations in Circular Shafts01:18

Stress Concentrations in Circular Shafts

Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
Transformation of Plane Stress01:18

Transformation of Plane Stress

Studying stress transformation is essential in understanding how stress components within a material, like a cube under plane stress, change with rotation. This change is analyzed by considering a prismatic element within the cube. As the element rotates, the stress components acting on it—both normal and shearing stresses—change in magnitude and orientation. This change is quantified using trigonometric functions of the rotation angle, relating the forces acting on the rotated element's faces...
General State of Stress01:21

General State of Stress

The general state of stress within a material can be accurately depicted using a stress tensor. This tensor encapsulates the internal forces distributed within a material subjected to external forces or deformations.
Specifically, consider a tetrahedral element where one face, labeled XYZ, is perpendicular to the line OA, and the remaining faces align with the coordinate axes with point O as the origin. At any point, such as point O, the stress tensor can be used to determine the stress...