Related Experiment Video

Updated: Jan 19, 2026

Operation of the Collaborative Composite Manufacturing CCM System
10:09

Operation of the Collaborative Composite Manufacturing CCM System

Published on: October 1, 2019

7.1K

Limits of the Process of Rotational Compression of Hollow Stepped Shafts

Jarosław Bartnicki1, Janusz Tomczak2, Zbigniew Pater3

  • 1Faculty of Mechanical Engineering, Lublin University of Technology, 36 Nadbystrzycka Str, 20-618 Lublin, Poland. j.bartnicki@pollub.pl.

Materials (Basel, Switzerland)
|September 25, 2019
PubMed

Keywords:
hollow stepped shaftsprocess limitsrotational compression

More Related Videos

Experimental Procedure for Warm Spinning of Cast Aluminum Components07:36

Experimental Procedure for Warm Spinning of Cast Aluminum Components

Published on: February 1, 2017

9.9K
Finite Element Modeling for the Simulation of the Quasi-Static Compression of Corrugated Tapered Tubes06:34

Finite Element Modeling for the Simulation of the Quasi-Static Compression of Corrugated Tapered Tubes

Published on: January 6, 2023

3.1K

Related Concept Videos

Transmission Shafts: Problem Solving01:09

Transmission Shafts: Problem Solving

Designing a solid shaft that transmits power from a motor to a machine tool involves a series of calculations to ensure the shaft can withstand the stresses applied by bending moments and torques. First, calculate the torque exerted on the gear, considering the power transmitted by the shaft and its rotational speed. Following this, compute the tangential forces acting on the gears, which directly relate to the torque and the gear radius.
Next, use bending moment diagrams for the shaft to...
493
Deformation in a Circular Shaft01:10

Deformation in a Circular Shaft

One of the distinctive characteristics of circular shafts is their ability to maintain their cross-sectional integrity under torsion. In other words, each cross-section continues to exist as a flat, unaltered entity, simply rotating like a solid, rigid slab. To understand the distribution of shearing stress within such a shaft, consider a cylindrical section inside this circular shaft. This section has a length of L and a radius of R, with one end fixed. The radius of the cylindrical section is...
875
Thin-Walled Hollow Shafts01:15

Thin-Walled Hollow Shafts

In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution of...
543
Circular Shafts - Elastoplastic Materials01:24

Circular Shafts - Elastoplastic Materials

The study of solid circular shafts under stress shows that within the elastic limit, stress increases directly to the distance from the shaft's center. This relationship holds until the shaft reaches a critical point of stress, beyond which it begins to yield, marking the transition from elastic to plastic deformation. At this crucial juncture, the maximum torque the shaft can endure without permanent deformation is determined, signifying the limit of its elastic behavior.
As torque on the...
469
Design of Transmission Shafts - Stress Analysis01:15

Design of Transmission Shafts - Stress Analysis

Designing a transmission shaft requires a thorough understanding of the stresses induced by bending moments and torques, especially in systems where power is transferred through gears. These forces create force-couple systems at the centers of the shaft's cross-sections, leading to both transverse and torsional loading. Although shearing stresses from transverse loads are typically smaller than those from torques and are often overlooked, the significant normal stresses from these loads...
712
Stress Concentrations in Circular Shafts01:18

Stress Concentrations in Circular Shafts

Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
545