Related Experiment Video

Updated: Jan 4, 2026

Ice Generation and the Heat and Mass Transfer Phenomena of Introducing Water to a Cold Bath of Brine
08:16

Ice Generation and the Heat and Mass Transfer Phenomena of Introducing Water to a Cold Bath of Brine

Published on: March 13, 2017

14.3K

Experimental estimates of compression heating and decompression cooling in ethylene glycol

J Steele1, J Ames1, M P Augustine1

  • 1Department of Chemistry, One Shields Avenue, University of California, Davis, CA.

Magnetic Resonance in Chemistry : MRC
|November 1, 2019
PubMed

Keywords:
1HNMRcompression heatingdecompression coolingpressure standard

More Related Videos

Measuring the Densities of Aqueous Glasses at Cryogenic Temperatures09:50

Measuring the Densities of Aqueous Glasses at Cryogenic Temperatures

Published on: June 28, 2017

9.0K
Fast Pyrolysis of Biomass Residues in a Twin-screw Mixing Reactor07:30

Fast Pyrolysis of Biomass Residues in a Twin-screw Mixing Reactor

Published on: September 9, 2016

28.2K

Related Concept Videos

Freezing Point Depression and Boiling Point Elevation03:12

Freezing Point Depression and Boiling Point Elevation

Boiling Point Elevation
The boiling point of a liquid is the temperature at which its vapor pressure is equal to ambient atmospheric pressure. Since the vapor pressure of a solution is lowered due to the presence of nonvolatile solutes, it stands to reason that the solution’s boiling point will subsequently be increased. Vapor pressure increases with temperature, and so a solution will require a higher temperature than will pure solvent to achieve any given vapor pressure, including one...
39.2K
Work Done in an Adiabatic Process01:20

Work Done in an Adiabatic Process

Consider the adiabatic compression of an ideal gas in the cylinder of an automobile diesel engine. The gasoline vapor is injected into the cylinder of an automobile engine when the piston is in its expanded position. The temperature, pressure, and volume of the resulting gas-air mixture are 20 °C, 1.00 x 105 N/m2, and 240 cm3 , respectively. The mixture is then compressed adiabatically to a volume of 40 cm3. Note that, in the actual operation of an automobile engine, the compression is not...
4.1K
Heating and Cooling Curves02:44

Heating and Cooling Curves

When a substance—isolated from its environment—is subjected to heat changes, corresponding changes in temperature and phase of the substance is observed; this is graphically represented by heating and cooling curves.
For instance, the addition of heat raises the temperature of a solid; the amount of heat absorbed depends on the heat capacity of the solid (q = mcsolidΔT). According to thermochemistry, the relation between the amount of heat absorbed or released by a substance, q, and its...
26.4K
Joule-Thomson Effect01:21

Joule-Thomson Effect

The Joule-Thomson effect, also known as the Joule-Kelvin effect, describes the temperature change of a fluid when it is forced through a valve or porous plug while keeping it in a thermally insulated environment. This experiment is called a throttling process. This is an important effect widely used in refrigeration and the liquefaction of gases.
This experiment forces high-pressure gas through a throttle valve or a porous plug to a lower-pressure region. The gas expands as it passes through to...
8.8K
Adiabatic Processes for an Ideal Gas01:18

Adiabatic Processes for an Ideal Gas

When an ideal gas is compressed adiabatically, that is, without adding heat, work is done on it, and its temperature increases. In an adiabatic expansion, the gas does work, and its temperature drops. Adiabatic compressions actually occur in the cylinders of a car, where the compressions of the gas-air mixture take place so quickly that there is no time for the mixture to exchange heat with its environment. Nevertheless, because work is done on the mixture during the compression, its...
3.9K
Heat Flow and Specific Heat01:12

Heat Flow and Specific Heat

Heat is a type of energy transfer that is caused by a temperature difference, and it can change the temperature of an object. Since heat is a form of energy, its SI unit is the joule (J). Another common unit of energy often used for heat is the calorie (cal), which is defined as the energy needed to change the temperature of 1 g of water by 1 °C, specifically between 14.5 °C and 15.5 °C, since the energy needed shows a slight temperature dependence. Another commonly used unit is...
6.5K