Related Experiment Video

Updated: Jan 4, 2026

Fabrication of High Contrast Gratings for the Spectrum Splitting Dispersive Element in a Concentrated Photovoltaic System
12:08

Fabrication of High Contrast Gratings for the Spectrum Splitting Dispersive Element in a Concentrated Photovoltaic System

Published on: July 18, 2015

11.1K

Comparative analysis for different designs of two-dimensional binary sinusoidal transmission gratings

Shlomi Lightman, Jonathan M Wengrowicz, Eran Daniel

    Applied Optics
    |November 2, 2019
    PubMed

    More Related Videos

    Measurement of X-ray Beam Coherence along Multiple Directions Using 2-D Checkerboard Phase Grating10:39

    Measurement of X-ray Beam Coherence along Multiple Directions Using 2-D Checkerboard Phase Grating

    Published on: October 11, 2016

    10.1K
    Patterning via Optical Saturable Transitions - Fabrication and Characterization08:19

    Patterning via Optical Saturable Transitions - Fabrication and Characterization

    Published on: December 11, 2014

    7.2K

    Related Concept Videos

    Graphical and Analytic Representation of Sinusoids01:20

    Graphical and Analytic Representation of Sinusoids

    Analyzing two sinusoidal voltages with equal amplitude and period but different phases on an oscilloscope, an instrument used to display and analyze waveforms, involves a three-step process.
    The first step is measuring the peak-to-peak value, which is twice the amplitude of the sinusoid. This provides information about the maximum voltage swing of the waveform.
    Secondly, the period and angular frequency are determined. The period is the time taken for one complete cycle of the waveform, while...
    856
    Transmission Line Design Considerations01:23

    Transmission Line Design Considerations

    Aluminum has become the material of choice for overhead transmission lines, surpassing copper due to its abundance and cost-effectiveness. The most prevalent type is the aluminum conductor, steel-reinforced (ACSR), which combines aluminum strands around a steel core. Other variants include all-aluminum conductors (AAC), all-aluminum alloy conductors (AAAC), aluminum conductor alloy-reinforced (ACAR), and aluminum-clad steel conductors. Advanced designs, such as aluminum conductors with steel...
    567
    Design of Transmission Shafts - Stress Analysis01:15

    Design of Transmission Shafts - Stress Analysis

    Designing a transmission shaft requires a thorough understanding of the stresses induced by bending moments and torques, especially in systems where power is transferred through gears. These forces create force-couple systems at the centers of the shaft's cross-sections, leading to both transverse and torsional loading. Although shearing stresses from transverse loads are typically smaller than those from torques and are often overlooked, the significant normal stresses from these loads...
    696
    Design Example: Aggregate Gradation01:24

    Design Example: Aggregate Gradation

    The right type and quality of aggregates are crucial for concrete as they significantly influence its properties, mix proportions, and cost-effectiveness. If different sources are available for sand, the commonly used fine aggregate in concrete, the selection of sand is primarily based on its gradation.
    The grading, or particle-size distribution, of sand is determined using sieve analysis, with standard sizes ranging from 150 μm to 10 mm (ASTM No. 100 sieve to 3⁄8 in. sieve). Sand is...
    278
    Bewley Lattice Diagram01:12

    Bewley Lattice Diagram

    The Bewley lattice diagram, developed by L. V. Bewley, effectively organizes the reflections occurring during transmission-line transients. It visually represents how voltage waves propagate and reflect within a transmission line, making it easier to understand the complex interactions that occur.
    1.4K
    Design of Transmission Shafts01:16

    Design of Transmission Shafts

    The design of a transmission shaft is governed by two primary specifications: the power it transmits and its rotational speed. These parameters guide the selection of the shaft's material and cross-sectional dimensions, ensuring that the material's maximum shearing stress remains within the elastic limit while transmitting the desired power at the given speed. The system's power is intrinsically linked to the applied torque. The torque applied to the shaft can be calculated by reconfiguring the...
    701