Related Experiment Video

Updated: Jan 4, 2026

Fabrication And Characterization Of Photonic Crystal Slow Light Waveguides And Cavities
11:08

Fabrication And Characterization Of Photonic Crystal Slow Light Waveguides And Cavities

Published on: November 30, 2012

19.4K

Z-domain modeling approach of a multilayer sextuple-coupled micro-ring resonator with 1 × 5 input-output bus

Binshati Chatterjee, Sanjoy Mandal

    Applied Optics
    |November 2, 2019
    PubMed

    More Related Videos

    Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters15:25

    Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters

    Published on: February 4, 2018

    6.5K
    Fabrication and Characterization of High-Q Silicon Nitride Membrane Resonators09:46

    Fabrication and Characterization of High-Q Silicon Nitride Membrane Resonators

    Published on: August 8, 2025

    1.0K

    Related Concept Videos

    Bus Impedance Matrix01:24

    Bus Impedance Matrix

    Calculating subtransient fault currents for three-phase faults in an N-bus power system involves using the positive-sequence network. When a three-phase short circuit occurs at a specific bus, the analysis uses the superposition method to evaluate two separate circuits.
    In the first circuit, all machine voltage sources are short-circuited, leaving only the prefault voltage source at the fault location. The positive-sequence bus impedance matrix can be determined by solving the nodal equations,...
    477
    Design Example: Capacitance Multiplier Circuit01:20

    Design Example: Capacitance Multiplier Circuit

    In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
    The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
    1.4K
    Cascaded Op Amps01:16

    Cascaded Op Amps

    Operational amplifiers (op-amps) are versatile electronic components that can be interconnected in a cascade - one after another in a linear sequence. This cascading is possible due to their infinite input resistance and zero output resistance, allowing them to maintain their input-output relationships even when connected in series.
    In a cascaded system, each op-amp is referred to as a stage. The output of one stage drives the input of the subsequent stage. As the input signal passes through...
    1.0K
    Design Example: Underdamped Parallel RLC Circuit01:17

    Design Example: Underdamped Parallel RLC Circuit

    Consider designing an oscillator circuit, a crucial component in various electronic devices and systems. The objective is to create an oscillator circuit with specific characteristics: a damped natural frequency of 4 kHz and a damping factor of 4 radians per second. To accomplish this, a parallel RLC circuit is employed, known for its ability to sustain oscillations at a resonant frequency. In this case, the damping factor is pivotal in achieving the desired performance.
    Starting with a fixed...
    592
    RLC Circuit as a Damped Oscillator01:30

    RLC Circuit as a Damped Oscillator

    An RLC circuit combines a resistor, inductor, and capacitor, connected in a series or parallel combination.
    Consider a series RLC circuit. Here, the presence of resistance in the circuit leads to energy loss due to joule heating in the resistance. Therefore, the total electromagnetic energy in the circuit is no longer constant and decreases with time. Since the magnitude of charge, current, and potential difference continuously decreases, their oscillations are said to be damped. This is...
    2.0K
    Design Example01:23

    Design Example

    The innovation of touch-tone telephony revolutionized the telecommunications industry by replacing the traditional rotary dial with a dual-tone multi-frequency (DTMF) signaling system. This system uses a matrix-style keypad with buttons arranged in four rows and three columns, creating 12 distinct signals each assigned to a pair of frequencies. Each button press results in a simultaneous generation of two sinusoidal tones – one from a low-frequency group (697 to 941 Hz) and one from a...
    503