Related Experiment Video

Updated: Jan 4, 2026

Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material

Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material

Published on: December 20, 2024

Effect of monolithic CAD-CAM ceramic thickness on resin cement polymerization: An in-vitro study

Mustafa B Donmez¹, Munir T Yucel²

¹Dentapol Dental Clinic, Ankara, Turkey, borgadonmez@gmail.com.

American Journal of Dentistry

|November 2, 2019

Abstract

Purpose:

To evaluate the effect of different thicknesses of CAD-CAM ceramic sections on the polymerization of two different resin cements.

Methods:

Three CAD-CAM all-ceramic restorative materials were sectioned with four different thicknesses. A total of 240 resin cement specimens were prepared from light cured and dual cure resin cements and absorption peaks were recorded. 10 samples of each resin cement were examined before and after polymerization and served as the control group. Data were analyzed using one-way ANOVA, independent t- and Tukey HSD tests (P< 0.05).

Results:

Control group showed the highest DOC values while samples cured under Vita Enamic section with a thickness of 2 mm presented the lowest values (P< 0.05). Polymerization performed under sections of 0.5 and 1 mm thicknesses provided statistically higher values. Dual cured resin cement samples showed higher DOC values compared to light cured resin cement samples. IPS Empress CAD sections with 0.5 and 1 mm thickness exhibited statistically higher values than other ceramics of the same thickness for light cured resin cement samples. A significant difference was observed between IPS Empress CAD and Vita Enamic while comparing ceramic sections of the same thickness (P< 0.05). There was no difference for sections of 1.5 and 2 mm (P>> 0.05).

Clinical Significance:

Thickness of the restorative material for an indirect restoration is a key element to determine the type of resin cement.

More Related Videos

Multi-material Ceramic-Based Components – Additive Manufacturing of Black-and-white Zirconia Components by Thermoplastic 3D-Printing (CerAM - T3DP)

Multi-material Ceramic-Based Components – Additive Manufacturing of Black-and-white Zirconia Components by Thermoplastic 3D-Printing (CerAM - T3DP)

Published on: January 7, 2019

Additive Manufacturing of Functionally Graded Ceramic Materials by Stereolithography

Additive Manufacturing of Functionally Graded Ceramic Materials by Stereolithography

Published on: January 25, 2019

Related Concept Videos

Porosity in Cement Paste

Porosity in Cement Paste

The porosity of concrete is a measure of the void spaces within its structure. These spaces impact its strength and durability significantly. When water and cement interact, a chemical reaction called hydration creates a semi-solid paste. This paste includes combined water, making up approximately 23% of the cement's dry mass, and gel water, which fills minuscule voids known as gel pores, accounting for about 28% of the cement gel volume.
The balance of water to cement in the mix is...

Accelerated Curing of Concrete

Accelerated Curing of Concrete

Accelerating concrete curing is achieved by applying heat and additional moisture. This process accelerates the hydration of the cement, resulting in an earlier strength gain in the concrete. Steam curing is a method wherein the concrete products are either transported through a chamber on a conveyor belt or encased in plastic, allowing steam at atmospheric pressure to circulate freely around them. This process begins with a phase of moist curing that typically lasts between 3 to 5 hours, after...

Articles linked to this work by shared authors, journal, and citation graph.

Effect of prolonged application of single-step self-etching primer and hydrofluoric acid on the surface roughness and shear bond strength of CAD/CAM materials.

European journal of oral sciences·2020

See all related articles