Related Experiment Video

Updated: Jan 1, 2026

A Novel Stretching Platform for Applications in Cell and Tissue Mechanobiology
16:46

A Novel Stretching Platform for Applications in Cell and Tissue Mechanobiology

Published on: June 3, 2014

12.2K

Continuum theory of bending-to-stretching transition

O U Salman1, G Vitale2, L Truskinovsky3

  • 1CNRS, LSPM UPR3407, Université Paris 13, Sorbonne Paris Cité, 93430 Villetaneuse, France.

Physical Review. E
|December 25, 2019
PubMed

More Related Videos

Biaxial Mechanical Characterizations of Atrioventricular Heart Valves11:00

Biaxial Mechanical Characterizations of Atrioventricular Heart Valves

Published on: April 9, 2019

14.8K
Author Spotlight: Enhancing Accuracy and Reproducibility in Whole Bone Bending Tests04:20

Author Spotlight: Enhancing Accuracy and Reproducibility in Whole Bone Bending Tests

Published on: September 1, 2023

1.3K

Related Concept Videos

Residual Stresses in Bending01:18

Residual Stresses in Bending

In the study of elastoplastic members subjected to bending moments, understanding the loading and unloading phases is crucial for assessing material behavior and structural integrity. During the loading phase, as the bending moment increases, the material initially responds elastically, adhering to Hooke's Law, where stress is directly proportional to strain. When the load exceeds the yield strength, plastic deformation occurs, resulting in permanent strain and deformation that remains even...
473
Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
328
Plastic Behavior01:21

Plastic Behavior

A material's elastic behavior is characterized by the disappearance of stress once the load is removed, allowing the material to return to its original state. However, when stress surpasses the yield point, yielding commences, marking the onset of plastic deformation or permanent set. This change from elastic to plastic behavior is influenced by the peak stress value and the duration before the load is removed. An intriguing observation occurs when a specimen is loaded, unloaded, and...
475
Bending of Curved Members - Strain Analysis01:14

Bending of Curved Members - Strain Analysis

The mechanics of deformation in curved members, such as beams or arches, under bending moments, involve complex responses. When such a member, symmetric about the y-axis and shaped like a segment of a circle centered at point C, is subjected to equal and opposite forces, its curvature and surface lengths change significantly. This alteration results in the shift of the curvature's center from C to C', indicating a tighter curve.
The important part of bending analysis for such a member...
454
Bending01:10

Bending

Pure bending is a fundamental concept in structural mechanics, essential for understanding how materials deform under symmetrical loads without direct forces. Pure bending occurs when prismatic members, such as beams, are subjected to equal and opposite moments that induce bending. The phenomenon is crucial as it allows for predicting stress distributions without the influence of axial or shear forces.
In pure bending, the bending stress in a beam is calculated based on the bending moment and...
775
Flexural Stress01:16

Flexural Stress

When analyzing bending in symmetric members, it's crucial to understand how stresses distribute when subjected to bending moments. This stress distribution is effectively described by applying fundamental mechanics and material science principles, particularly Hooke's Law for elastic materials.
Hooke's Law states that within the material's elastic limits, stress is directly proportional to strain. In a member experiencing a bending moment, the strain at any point is relative to its distance...
626