Related Experiment Video

Updated: Dec 31, 2025

Automation of Mode Locking in a Nonlinear Polarization Rotation Fiber Laser through Output Polarization Measurements
14:18

Automation of Mode Locking in a Nonlinear Polarization Rotation Fiber Laser through Output Polarization Measurements

Published on: February 28, 2016

11.8K

Control of Acousto-Optic Mode Locker by Means of Electronic Matching Circuit

Grigorii Slinkov, Sergey N Mantsevich, Vladimir I Balakshy

    IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
    |January 7, 2020
    PubMed

    More Related Videos

    Fabrication and Testing of Microfluidic Optomechanical Oscillators09:10

    Fabrication and Testing of Microfluidic Optomechanical Oscillators

    Published on: May 29, 2014

    12.6K
    Characterization of Anisotropic Leaky Mode Modulators for Holovideo09:36

    Characterization of Anisotropic Leaky Mode Modulators for Holovideo

    Published on: March 19, 2016

    8.3K

    Related Concept Videos

    Mesh Analysis for AC Circuits01:12

    Mesh Analysis for AC Circuits

    In the domain of radio communication, the significance of impedance matching must be considered. It is crucial to ensure the efficient transmission of signals between radio transmitters and receivers. Achieving this balance involves using impedance-matching circuits, with one fundamental configuration comprising a resistor, capacitor, and inductor.
    The process of harmonizing these impedances begins with a clear understanding of the input and output signals. Once these signals are known, the...
    625
    Oscillations In An LC Circuit01:30

    Oscillations In An LC Circuit

    An idealized LC circuit of zero resistance can oscillate without any source of emf by shifting the energy stored in the circuit between the electric and magnetic fields. In such an LC circuit, if the capacitor contains a charge q before the switch is closed, then all the energy of the circuit is initially stored in the electric field of the capacitor. This energy is given by
    2.9K
    Line Protection with Impedance Relays01:27

    Line Protection with Impedance Relays

    Coordinating time-delay overcurrent relays in complex radial systems and directional overcurrent relays in multi-source transmission loops can be challenging. Impedance relays address these issues by responding to the voltage-to-current ratio, specifically measuring the apparent impedance of a line. These relays become more sensitive during faults as current increases and voltage decreases, thereby reducing the apparent impedance.
    Under normal conditions, low load currents keep the measured...
    391
    Magnetic Damping01:17

    Magnetic Damping

    Eddy currents can produce significant drag on motion, called magnetic damping. For instance, when a metallic pendulum bob swings between the poles of a strong magnet, significant drag acts on the bob as it enters and leaves the field, quickly damping the motion.
    If, however, the bob is a slotted metal plate, the magnet produces a much smaller effect. When a slotted metal plate enters the field, an emf is induced by the change in flux; however, it is less effective because the slots limit the...
    963
    Op Amp AC Circuits01:18

    Op Amp AC Circuits

    Within an audio system, the filter circuit plays a pivotal role in processing the amplified audio signal from an amplifier. Its primary function is significantly attenuating signal components with lower frequencies, thereby shaping the audio output. This circuit's operations are examined, focusing on the fundamental filter configuration. This configuration involves an operational amplifier arranged in an inverting setup coupled with resistors (R1 and R2) and a capacitor (C1).
    439
    RLC Circuit as a Damped Oscillator01:30

    RLC Circuit as a Damped Oscillator

    An RLC circuit combines a resistor, inductor, and capacitor, connected in a series or parallel combination.
    Consider a series RLC circuit. Here, the presence of resistance in the circuit leads to energy loss due to joule heating in the resistance. Therefore, the total electromagnetic energy in the circuit is no longer constant and decreases with time. Since the magnitude of charge, current, and potential difference continuously decreases, their oscillations are said to be damped. This is...
    2.0K