Related Experiment Video

Updated: Dec 25, 2025

Continuous Instream Monitoring of Nutrients and Sediment in Agricultural Watersheds
12:50

Continuous Instream Monitoring of Nutrients and Sediment in Agricultural Watersheds

Published on: September 26, 2017

11.7K

Towards Safety Improvement of Measurement and Control Signals Transmission in Marine Environment

Romuald Masnicki1, Janusz Mindykowski1, Przemyslaw Grala2

  • 1Faculty of Electrical Engineering, Gdynia Maritime University, Morska 81-87, 81-225 Gdynia, Poland.

Sensors (Basel, Switzerland)
|March 21, 2020
PubMed

Keywords:
WiFiZigBeemarine environmentmeasurement and controlsafety improvementsignal transmissionwireless sensor network

More Related Videos

Continuous-Wave Propagation Channel-Sounding Measurement System - Testing, Verification, and Measurements09:36

Continuous-Wave Propagation Channel-Sounding Measurement System - Testing, Verification, and Measurements

Published on: June 25, 2021

3.4K
Manufacturing Simple and Inexpensive Soil Surface Temperature and Gravimetric Water Content Sensors08:49

Manufacturing Simple and Inexpensive Soil Surface Temperature and Gravimetric Water Content Sensors

Published on: December 21, 2019

10.0K

Related Concept Videos

Line Protection with Impedance Relays01:27

Line Protection with Impedance Relays

Coordinating time-delay overcurrent relays in complex radial systems and directional overcurrent relays in multi-source transmission loops can be challenging. Impedance relays address these issues by responding to the voltage-to-current ratio, specifically measuring the apparent impedance of a line. These relays become more sensitive during faults as current increases and voltage decreases, thereby reducing the apparent impedance.
Under normal conditions, low load currents keep the measured...
384
Bacterial Signaling01:30

Bacterial Signaling

Bacterial signaling can occur within bacteria (intracellular) or between bacteria (intercellular). At times, a group of bacteria behaves like a community. To achieve this, they engage in quorum sensing, the perception of higher cell density that causes changes in gene expression. Quorum sensing involves both extracellular and intracellular signaling. The signaling cascade starts with a molecule called an autoinducer (AI). Individual bacteria produce AIs that move out of the bacterial cell...
39.8K
Transmission Line Design Considerations01:23

Transmission Line Design Considerations

Aluminum has become the material of choice for overhead transmission lines, surpassing copper due to its abundance and cost-effectiveness. The most prevalent type is the aluminum conductor, steel-reinforced (ACSR), which combines aluminum strands around a steel core. Other variants include all-aluminum conductors (AAC), all-aluminum alloy conductors (AAAC), aluminum conductor alloy-reinforced (ACAR), and aluminum-clad steel conductors. Advanced designs, such as aluminum conductors with steel...
542
Pilot and Numeric Relaying01:21

Pilot and Numeric Relaying

Pilot relaying is a type of differential protection used in power systems. It compares electrical quantities at the terminals of equipment via a communication channel instead of direct relay interconnection. This method is essential for transmission lines where the terminals are far apart, typically up to 80 km for lines with 69 to 115 kV ratings. Four types of communication channels are used for pilot relaying:
431
Electronic Distance Measuring Instruments01:30

Electronic Distance Measuring Instruments

Electronic Distance Measuring Instruments (EDMs) are essential tools in modern surveying, offering precise distance measurements by emitting electromagnetic signals and calculating the time required for these signals to travel to a target and return. Two primary types of signals are used in EDMs — light waves and microwaves — each suited to specific environmental and distance requirements. Light-wave-based EDMs utilize either infrared or laser light, providing high accuracy over...
384
Pipe Flowrate Measurement01:28

Pipe Flowrate Measurement

In pipe flow measurement, orifice, nozzle, and Venturi meters are commonly used to determine fluid flowrates by constricting the flow area, which increases fluid velocity and reduces pressure. This pressure difference, governed by Bernoulli's principle and adjusted for real-world conditions, is essential for calculating flowrate. Each meter type is suited to specific applications based on accuracy, efficiency, and compatibility with various flow conditions.
The orifice meter is a simple,...
1.1K