Related Experiment Video

Updated: Dec 25, 2025

A Coupled Experiment-finite Element Modeling Methodology for Assessing High Strain Rate Mechanical Response of Soft Biomaterials
11:28

A Coupled Experiment-finite Element Modeling Methodology for Assessing High Strain Rate Mechanical Response of Soft Biomaterials

Published on: May 18, 2015

12.9K

A Comparison of Experimental and Theoretical Relations Between Young's Modulus and the Flexural and Longitudinal

S Spinner, T W Reichard, W E Tefft

    Journal of Research of the National Bureau of Standards. Section A, Physics and Chemistry
    |March 21, 2020
    PubMed

    More Related Videos

    Cutting Procedures, Tensile Testing, and Ageing of Flexible Unidirectional Composite Laminates07:53

    Cutting Procedures, Tensile Testing, and Ageing of Flexible Unidirectional Composite Laminates

    Published on: April 27, 2019

    8.6K
    Ultrasonic Fatigue Testing in the Tension-Compression Mode06:54

    Ultrasonic Fatigue Testing in the Tension-Compression Mode

    Published on: March 7, 2018

    11.1K

    Related Concept Videos

    Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

    Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

    Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.
    473
    Bending of Members Made of Several Materials01:11

    Bending of Members Made of Several Materials

    In analyzing a structural member composed of two different materials with identical cross-sectional areas, it is crucial to understand how their distinct elastic properties affect the member's response under load. The analysis involves assessing stress and strain distributions using the transformed section concept, which accounts for variations in material properties.
    Hooke's Law determines stress in each material, stating that stress is proportional to strain but varies due to each material's...
    502
    Flexural Stress01:16

    Flexural Stress

    When analyzing bending in symmetric members, it's crucial to understand how stresses distribute when subjected to bending moments. This stress distribution is effectively described by applying fundamental mechanics and material science principles, particularly Hooke's Law for elastic materials.
    Hooke's Law states that within the material's elastic limits, stress is directly proportional to strain. In a member experiencing a bending moment, the strain at any point is relative to its distance...
    606
    Hooke's Law01:26

    Hooke's Law

    Hooke's law, a pivotal principle in material science, establishes that the strain a material undergoes is directly proportional to the applied stress, defined by a factor called the modulus of elasticity or Young's modulus.
    1.3K
    Dynamic Modulus of Elasticity of Concrete01:16

    Dynamic Modulus of Elasticity of Concrete

    The dynamic modulus of elasticity assesses how a concrete structure deforms under impact or dynamic loads. It is typically higher than the static modulus of elasticity, measured under slow, steady loading conditions.
    The sonic test is a common method to determine the dynamic modulus. In this test, a concrete beam, sized either 6 x 6 x 30 inches or 4 x 4 x 20 inches, is clamped at its center. Vibrations are initiated at one end of the beam by an electromagnetic exciter unit powered by a...
    852
    Torsion of Noncircular Members01:16

    Torsion of Noncircular Members

    Circular shafts undergoing torsional stress maintain their cross-sectional integrity due to their axisymmetric nature. This symmetry ensures an even distribution of stress, allowing the shaft to withstand torsion without distorting. In contrast, square bars, lacking this axial symmetry, experience significant distortion across their cross-sections when subjected to torsion, with the exception of along their diagonals and at lines connecting midpoints. A detailed examination of a cubic element...
    448