Related Experiment Video

Updated: Dec 25, 2025

High-precision Electromagnetic Flowmeter with Empty Pipe Detection via Complex Programmable Logic Device-based Waveform Recognition
05:11

High-precision Electromagnetic Flowmeter with Empty Pipe Detection via Complex Programmable Logic Device-based Waveform Recognition

Published on: June 27, 2025

524

Design of small mode-dependent-loss scrambling-type mode (de)multiplexer based on PLC

Motoki Shirata, Takeshi Fujisawa, Taiji Sakamoto

    Optics Express
    |April 1, 2020
    PubMed

    More Related Videos

    Characterization of Anisotropic Leaky Mode Modulators for Holovideo09:36

    Characterization of Anisotropic Leaky Mode Modulators for Holovideo

    Published on: March 19, 2016

    8.2K
    Quasi-light Storage for Optical Data Packets07:45

    Quasi-light Storage for Optical Data Packets

    Published on: February 6, 2014

    11.2K

    Related Concept Videos

    Design Example: Capacitance Multiplier Circuit01:20

    Design Example: Capacitance Multiplier Circuit

    In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
    The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
    1.3K
    Line Protection with Impedance Relays01:27

    Line Protection with Impedance Relays

    Coordinating time-delay overcurrent relays in complex radial systems and directional overcurrent relays in multi-source transmission loops can be challenging. Impedance relays address these issues by responding to the voltage-to-current ratio, specifically measuring the apparent impedance of a line. These relays become more sensitive during faults as current increases and voltage decreases, thereby reducing the apparent impedance.
    Under normal conditions, low load currents keep the measured...
    384
    Block Diagram Reduction01:22

    Block Diagram Reduction

    The process of deriving the transfer function of a control system often involves reducing its block diagram to a single block. This simplification can be achieved through a series of strategic operations, including relocating branch points and comparators. These operations preserve the overall function of the system while allowing for easier manipulation and combination of blocks.
    The first step in this process is the identification and relocation of a branch point. A branch point, where a...
    442
    Clamper Circuit01:14

    Clamper Circuit

    A clamper circuit, also known as a DC restorer, represents a specialized variant of the rectifier circuit, notable for its method of taking the output across the diode rather than the capacitor. This configuration lends to several distinctive applications, particularly in handling square wave inputs.
    Within this circuit, the diode's orientation prompts the capacitor to charge up to the level of the most negative peak of the input signal. Upon reaching this state, the diode ceases to...
    884
    Clipper Circuit01:18

    Clipper Circuit

    A clipper circuit is a fundamental wave-shaping device that harnesses the unique properties of diodes to alter and control waveform characteristics. This technology is widely used in electronic devices, especially in television and radar communication systems, where it enhances waveform modulation in both transmitters and receivers.
    The operation of a clipper circuit can be exemplified by analyzing a dual-clipper configuration setup that integrates two ideal diodes, each paired with a biasing...
    789
    Design Example01:23

    Design Example

    The innovation of touch-tone telephony revolutionized the telecommunications industry by replacing the traditional rotary dial with a dual-tone multi-frequency (DTMF) signaling system. This system uses a matrix-style keypad with buttons arranged in four rows and three columns, creating 12 distinct signals each assigned to a pair of frequencies. Each button press results in a simultaneous generation of two sinusoidal tones – one from a low-frequency group (697 to 941 Hz) and one from a...
    483