Related Experiment Video

Updated: Dec 25, 2025

Assembly and Characterization of an External Driver for the Generation of Sub-Kilohertz Oscillatory Flow in Microchannels
08:32

Assembly and Characterization of an External Driver for the Generation of Sub-Kilohertz Oscillatory Flow in Microchannels

Published on: January 28, 2022

2.7K

High Temperature Adiabatic Heating in µ-IM Mould Cavities-A Case for Venting Design Solutions

Matthew Tucker1, Christian A Griffiths1, Andrew Rees1

  • 1College of Engineering, Swansea University, Swansea SA1 8EN, UK.

Micromachines
|April 3, 2020
PubMed

Keywords:
adiabatic heatingdiesel effectmicro injection mouldingventing

More Related Videos

Design and Optimization Strategies of a High-Performance Vented Box14:23

Design and Optimization Strategies of a High-Performance Vented Box

Published on: June 9, 2023

1.5K
Simulation of Early Earth Hydrothermal Chimneys in a Thermal Gradient Environment06:29

Simulation of Early Earth Hydrothermal Chimneys in a Thermal Gradient Environment

Published on: February 27, 2021

3.9K

Related Concept Videos

Thermal Insulation in Masonry Walls01:22

Thermal Insulation in Masonry Walls

In hot, dry climates, the thermal mass of masonry walls can be beneficial, absorbing heat during the day and releasing it at night, thereby stabilizing indoor temperatures. However, in most other climates, additional insulation is necessary to enhance thermal resistance.
External insulation can be applied using an Exterior Insulation and Finish System (EIFS), which involves affixing panels of plastic foam to the wall and covering them with a polymeric stucco reinforced with glass fiber mesh....
408
Masonry in Cold and Hot Weather Conditions01:21

Masonry in Cold and Hot Weather Conditions

In cold weather, masonry construction requires specific precautions to ensure mortar does not freeze before curing, as this can significantly weaken its strength and watertightness. Mortar temperature should be maintained between 60°F and 80°F to support proper hydration and curing. Below 40°F, mortar water must be heated, but should not exceed 120°F as high temperatures can reduce mortar's compressive and bond strength.
Other key practices include keeping masonry units...
286
Cavity Drainage and Flashings in Masonry walls01:20

Cavity Drainage and Flashings in Masonry walls

Typically, a cavity wall consists of two wythes separated by a gap of at least 2 inches, which may contain insulation while still maintaining a minimum clear space of 1 inch to facilitate adequate drainage. Advanced methods like the insertion of a continuous drainage mat can further reduce this space while ensuring effective moisture expulsion.
Weep holes, strategically placed at the base of the cavity, are critical for draining accumulated water. These openings are created by leaving head...
347
Pressure and Volume in an Adiabatic Process01:27

Pressure and Volume in an Adiabatic Process

Free expansion of a gas is an adiabatic process. However, there are few differences between free expansion and adiabatic expansion. During free expansion, no work is done, and there is no change in internal energy. But, for an adiabatic expansion, work is done, and there is a change in internal energy. During an adiabatic process, the relation between the pressure and volume is obtained from the condition for the adiabatic process, that is,
3.2K
Physical Methods for Controlling Microbial Growth: Temperature01:23

Physical Methods for Controlling Microbial Growth: Temperature

Heat is a widely used method to control microbial growth by targeting and denaturing cellular proteins, thereby killing or inactivating microbes. This method's effectiveness is quantified using parameters such as the thermal death point (TDP), thermal death time (TDT), and decimal reduction time (D value). TDP represents the lowest temperature at which all microorganisms in a liquid suspension are eliminated within 10 minutes, whereas TDT is the time necessary to achieve sterilization at a...
841
Thermal expansion and Thermal stress: Problem Solving01:27

Thermal expansion and Thermal stress: Problem Solving

San Francisco's Golden Gate Bridge is exposed to temperatures ranging from -15 °C to 40 °C. At its coldest, the main span of the bridge is 1275 m long. Assuming that the bridge is made entirely of steel, what is the change in its length between these temperatures?
To solve the problem, first, identify the known and unknown quantities. The initial length (L) of the bridge is 1275 m, the coefficient of linear expansion (α) for steel is 12 x 10-6/°C, and the change in temperature (ΔT) is 55...
2.0K