Related Experiment Video

Updated: Dec 23, 2025

Experimental Procedure for Warm Spinning of Cast Aluminum Components
07:36

Experimental Procedure for Warm Spinning of Cast Aluminum Components

Published on: February 1, 2017

9.8K

Temperature Dependence of Activation Energy in Stage II Recovery in Deformed Aluminium

T Tsuchida1, R Kaneko1

  • 1Department of Physics, Faculty of Science, Science University of Tokyo.

Physica Status Solidi (A): Applied Research
|April 25, 2020
PubMed

More Related Videos

Experimental Methods for Investigation of Shape Memory Based Elastocaloric Cooling Processes and Model Validation11:11

Experimental Methods for Investigation of Shape Memory Based Elastocaloric Cooling Processes and Model Validation

Published on: May 2, 2016

11.5K
Identification and Quantification of Decomposition Mechanisms in Lithium-Ion Batteries; Input to Heat Flow Simulation for Modeling Thermal Runaway11:25

Identification and Quantification of Decomposition Mechanisms in Lithium-Ion Batteries; Input to Heat Flow Simulation for Modeling Thermal Runaway

Published on: March 7, 2022

5.1K

Related Concept Videos

Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
321
Activation Energy01:26

Activation Energy

Activation energy is the minimum amount of energy necessary for a chemical reaction to move forward. The higher the activation energy, the slower the rate of the reaction. However, adding heat to the reaction will increase the rate, since it causes molecules to move faster and increase the likelihood that molecules will collide. The collision and breaking of bonds represents the uphill phase of a reaction and generates the transition state. The transition state is an unstable high-energy state...
85.9K
Bond Dissociation Energy and Activation Energy02:13

Bond Dissociation Energy and Activation Energy

Bond energy is the energy required to break a bond homolytically. These values are usually expressed in units of kcal/mol or kJ/mol and are referred to as bond dissociation energies when given for specific bonds or average bond energies when indicated for a given type of bond over many compounds. Firstly, the bond dissociation energy for a single bond is weaker than that of a double bond, which in turn is weaker than that of a triple bond. Secondly, hydrogen forms relatively strong bonds with...
10.5K
Acid-Catalyzed Hydration of Alkenes02:45

Acid-Catalyzed Hydration of Alkenes

Alkenes react with water in the presence of an acid to form an alcohol. In the absence of acid, hydration of alkenes does not occur at a significant rate, and the acid is not consumed in the reaction. Therefore, alkene hydration is an acid-catalyzed reaction.
16.8K
Strength and Heat of Hydration01:29

Strength and Heat of Hydration

The hydration of cement is an exothermic reaction in which heat is generated as cement hydrates. This heat of hydration is critical to cement's strength development. The rate at which this heat is generated affects the temperature rise, with a majority of the heat being released early in the hydration process, half within the first three days, and about 75% within the first week.
The heat of hydration for each cement compound is significant; for instance, tricalcium aluminate (C3A) and...
563
Arrhenius Plots02:34

Arrhenius Plots

The Arrhenius equation relates the activation energy and the rate constant, k, for chemical reactions. In the Arrhenius equation, k = Ae−Ea/RT, R is the ideal gas constant, which has a value of 8.314 J/mol·K, T is the temperature on the kelvin scale, Ea is the activation energy in J/mole, e is the constant 2.7183, and A is a constant called the frequency factor, which is related to the frequency of collisions and the orientation of the reacting molecules.
The Arrhenius equation can be used...
46.2K