Related Experiment Video

Updated: Dec 20, 2025

Scanning SQUID Study of Vortex Manipulation by Local Contact
06:53

Scanning SQUID Study of Vortex Manipulation by Local Contact

Published on: February 1, 2017

7.1K

Incipient tip vortex cavitation localization using block-sparse compressive sensing

Minseuk Park1, Yongsung Park1, Keunhwa Lee2

  • 1Department of Naval Architecture and Ocean Engineering, Seoul National University, Seoul, 08826, Republic of Korea.

The Journal of the Acoustical Society of America
|June 4, 2020
PubMed

More Related Videos

Imaging and Quantification of the Area of Fast-Moving Microbubbles Using a High-Speed Camera and Image Analysis05:31

Imaging and Quantification of the Area of Fast-Moving Microbubbles Using a High-Speed Camera and Image Analysis

Published on: September 5, 2020

6.2K
Induction of Microstreaming by Nonspherical Bubble Oscillations in an Acoustic Levitation System08:19

Induction of Microstreaming by Nonspherical Bubble Oscillations in an Acoustic Levitation System

Published on: May 9, 2021

2.6K

Related Concept Videos

Uniform Depth Channel Flow: Problem Solving01:18

Uniform Depth Channel Flow: Problem Solving

To calculate the flow rate for a trapezoidal channel, first, identify the bottom width, side slope, and flow depth of the channel. The cross-sectional area (A) corresponding to the depth of flow (y), channel bottom width (B), and side slope (θ) is determined by:Next, calculate the wetted perimeter, which includes the bottom width and the sloped side lengths in contact with the water. Using the values of the cross-sectional area and the wetted perimeter, determine the hydraulic radius by...
363
Uniform Depth Channel Flow01:27

Uniform Depth Channel Flow

Uniform depth channel flow keeps fluid depth consistent along channels such as irrigation canals. In natural channels, such as rivers, approximate uniform flow is often assumed. This condition occurs when the channel’s bottom slope matches the energy slope, balancing potential energy lost from gravity with head loss due to shear stress. This balance prevents depth changes along the channel length, resulting in a steady, uniform flow.Uniform flow in open channels with a constant cross-section...
451
Standing Waves in a Cavity01:28

Standing Waves in a Cavity

A household microwave and lasers are examples of standing electromagnetic waves in a cavity. When two conducting metal plates are placed parallel at the nodal planes, it creates a cavity where standing waves are formed. The cavity between the two planes is analogous to a stretched string held at the points x = 0 and x = L. Here, the distance 'L' between the two planes must be an integer multiple of half of the wavelength. The wavelengths that satisfy this condition are given by:
1.3K
Turbulent Flow: Problem Solving01:09

Turbulent Flow: Problem Solving

Carbonation is a process used to dissolve carbon dioxide gas in a liquid, commonly used in the production of carbonated beverages. Achieving efficient carbonation requires careful control of temperature, pressure, and flow conditions. By adjusting these parameters, carbonation efficiency can be maximized, producing a higher concentration of CO2 in the liquid.
Temperature is a key factor in CO2 solubility. In this case, the CO2 gas and the liquid are cooled to 20°C. Lower temperatures enhance...
333
Turbulent Flow01:24

Turbulent Flow

Turbulent flow is characterized by unpredictable fluctuations in velocity and pressure, which result in a chaotic fluid movement distinct from the orderly patterns of laminar flow. While laminar flow is governed by smooth, parallel layers with minimal mixing, turbulent flow exhibits highly irregular, three-dimensional patterns. This behavior arises due to instabilities in the fluid's velocity profile, and amplifies as the flow velocity increases. Minor disturbances, known as turbulent...
566
Pressure Variation in a Fluid at Rest01:11

Pressure Variation in a Fluid at Rest

In a fluid at rest, the pressure at any point beneath the fluid surface depends solely on the depth, not on the container's shape or size. This principle, known as hydrostatic pressure, arises because, in stationary fluids, there is no acceleration, meaning the forces within the fluid balance out. Only vertical forces, caused by the weight of the fluid above, contribute to pressure changes with depth.
When measuring pressure at two different levels within the fluid, the difference in...
654