Related Experiment Video

Updated: Dec 13, 2025

Optimized Setup and Protocol for Magnetic Domain Imaging with In Situ Hysteresis Measurement
09:43

Optimized Setup and Protocol for Magnetic Domain Imaging with In Situ Hysteresis Measurement

Published on: November 7, 2017

9.8K

Magnetic Stress Sensing System for Nondestructive Stress Testing of Structural Steel and Steel Truss Components Based

Guangyuan Weng1, Jintao Wang1, Yang Liu2

  • 1Mechanical Engineering College, Xi'an Shiyou University, Xi'an 710065, China.

Sensors (Basel, Switzerland)
|July 26, 2020
PubMed

Keywords:
existing magnetismmagnetic sensing systemnondestructive teststeel structurestress detection

More Related Videos

Magnetic Resonance Derived Myocardial Strain Assessment Using Feature Tracking07:21

Magnetic Resonance Derived Myocardial Strain Assessment Using Feature Tracking

Published on: February 12, 2011

14.7K
Ferromagnetic Bare Metal Stent for Endothelial Cell Capture and Retention11:01

Ferromagnetic Bare Metal Stent for Endothelial Cell Capture and Retention

Published on: September 18, 2015

11.9K

Related Concept Videos

Mechanical Characteristics of Steel01:18

Mechanical Characteristics of Steel

The mechanical characteristics of steel are assessed through various tests that evaluate its strength, toughness, and flexibility. These tests include tension, torsion, impact, bending, and hardness assessments, each providing crucial information about steel's suitability for specific applications.
The tension test is fundamental for determining tensile strength. In this test, a steel specimen is stretched using a gripping device until it breaks. The data collected during this test are used...
928
Applications of Stress01:04

Applications of Stress

Consider a structure made of a boom and a rod designed to support a load. These two components are connected by a pin and stabilized by brackets and pins. The boom and the rod are detached from their supports to assess the different stresses imposed on this structure, and a free-body diagram is drawn. Then, all the forces applied, including the load acting on the structure, are identified. The reaction forces exerted on both the boom and the rod are computed using the equilibrium equations.
The...
533
General State of Stress01:21

General State of Stress

The general state of stress within a material can be accurately depicted using a stress tensor. This tensor encapsulates the internal forces distributed within a material subjected to external forces or deformations.
Specifically, consider a tetrahedral element where one face, labeled XYZ, is perpendicular to the line OA, and the remaining faces align with the coordinate axes with point O as the origin. At any point, such as point O, the stress tensor can be used to determine the stress...
512
Magnetic Damping01:17

Magnetic Damping

Eddy currents can produce significant drag on motion, called magnetic damping. For instance, when a metallic pendulum bob swings between the poles of a strong magnet, significant drag acts on the bob as it enters and leaves the field, quickly damping the motion.
If, however, the bob is a slotted metal plate, the magnet produces a much smaller effect. When a slotted metal plate enters the field, an emf is induced by the change in flux; however, it is less effective because the slots limit the...
895
Stress-Strain Diagram - Ductile Materials01:24

Stress-Strain Diagram - Ductile Materials

The stress-strain relationship in ductile materials such as structural steel or aluminium is intricate and progresses through several stages. When a specimen is loaded, it initially exhibits a linear length increase, depicted by a steep straight line on the stress-strain diagram. It indicates the material is elastically deforming and will return to its original shape once unloaded. However, when a critical stress value is reached, plastic deformation begins. This stage sees substantial...
1.7K
Stress Concentrations01:13

Stress Concentrations

The concept of stress concentration is crucial for understanding how materials respond under bending stresses, particularly when there are irregularities or discontinuities in the material's geometry. Normally, stress in a symmetric member subjected to pure bending is assumed to be uniformly distributed across the entire cross-section. However, this assumption does not hold when there are variations in the cross-sectional geometry or the presence of notches and holes.
The stress...
490