Related Experiment Video

Updated: Dec 13, 2025

Picoinjection of Microfluidic Drops Without Metal Electrodes
09:20

Picoinjection of Microfluidic Drops Without Metal Electrodes

Published on: April 18, 2014

11.5K

Electric Current Waveform of the Injector as a Source of Diagnostic Information

Krzysztof Więcławski1, Jędrzej Mączak1, Krzysztof Szczurowski1

  • 1Faculty of Automotive and Construction Machinery Engineering, Warsaw University of Technology, 02-524 Warsaw, Poland.

Sensors (Basel, Switzerland)
|July 30, 2020
PubMed

Keywords:
diagnosticsinductanceinjector

More Related Videos

Electric and Magnetic Field Devices for Stimulation of Biological Tissues13:29

Electric and Magnetic Field Devices for Stimulation of Biological Tissues

Published on: May 15, 2021

5.6K
High-precision Electromagnetic Flowmeter with Empty Pipe Detection via Complex Programmable Logic Device-based Waveform Recognition05:11

High-precision Electromagnetic Flowmeter with Empty Pipe Detection via Complex Programmable Logic Device-based Waveform Recognition

Published on: June 27, 2025

490

Related Concept Videos

Design Example: Automobile Ignition System01:14

Design Example: Automobile Ignition System

The automobile's ignition system plays a vital role by ensuring the timely ignition of the fuel-air mixture in each cylinder. This ignition is facilitated by a spark plug, which is composed of two electrodes separated by an air gap. A spark forms across this air gap when a substantial voltage is generated between the electrodes, leading to the ignition of the fuel.
One can generate a large voltage using a car battery of 12 volts with the help of inductors. Inductors are known for opposing...
450
Three-Phase Short Circuit—Unloaded Synchronous Machine01:21

Three-Phase Short Circuit—Unloaded Synchronous Machine

Conducting a three-phase short circuit test on an unloaded synchronous machine helps understand its impact on the system. The AC fault current's oscillogram, with the DC offset removed, reveals that the waveform amplitude decreases from an initially high value to a steady-state level for one phase of the machine.
This behavior occurs due to the magnetic flux produced by the short-circuit armature currents. Initially, these currents follow high-reluctance paths but eventually shift to...
557
Electrical Current01:10

Electrical Current

Electrical current is defined as the rate at which charge flows. When there is a large current present, such as that used to run a refrigerator, a large amount of charge moves through the wire in a small amount of time. If the current is small, such as that used to operate a handheld calculator, a small amount of charge moves through the circuit over a long period of time. The SI unit for current is the ampere (A), named for the French physicist André-Marie Ampère (1775–1836).
6.6K
Electric Generator: Alternator01:25

Electric Generator: Alternator

Electric generators induce an emf by rotating a coil in a magnetic field. A simple alternator is an AC generator that creates electrical energy that varies sinusoidally with time. A simple alternator consists of a conducting loop that is placed inside a uniform magnetic field. The loop is connected to split rings connected to the external circuit with the help of brushes.
The magnetic flux passing through the coil varies sinusoidally as the loop rotates inside the magnetic field. This...
3.1K
AC Sources01:20

AC Sources

Direct current is a flow of electric charge in only one direction and has a steady state of constant voltage in the circuit. Rectifiers, batteries, commutator-equipped generators, and fuel cells are some examples of devices that generate direct current. Nowadays, most applications use a time-varying voltage source. Alternating current is a flow of electric charge that periodically reverses direction. An alternating current is produced by an alternating emf that is generated in a power plant. If...
3.6K
Instrument Transformers01:23

Instrument Transformers

Instrument transformers, comprising voltage transformers (VTs) and current transformers (CTs), play crucial roles in power substations by providing isolated replicas of current or voltage for measurement and protection purposes. Voltage transformers reduce the primary voltage to levels suitable for relay operation and measurement, while current transformers scale down the primary current. The primary winding of a current transformer often consists of a single turn, achieved by threading the...
366