Related Experiment Video

Updated: Dec 13, 2025

Measurements of Local Instantaneous Convective Heat Transfer in a Pipe - Single and Two-phase Flow
08:25

Measurements of Local Instantaneous Convective Heat Transfer in a Pipe - Single and Two-phase Flow

Published on: April 30, 2018

7.5K

An experimental analysis of acoustic input impedance of a narrow pipe with low Mach number flow and thermal gradient

Ashkan Zaker1, Vincent Gibiat2, Stephane Guilain1

  • 1Renault SAS, Département Fluides Moteur, 1 Allée Cornuel, 91510 Lardy, France.

The Journal of the Acoustical Society of America
|August 6, 2020
PubMed

More Related Videos

Analyzing Mixing Inhomogeneity in a Microfluidic Device by Microscale Schlieren Technique10:12

Analyzing Mixing Inhomogeneity in a Microfluidic Device by Microscale Schlieren Technique

Published on: June 12, 2015

9.4K
Investigating the Three-dimensional Flow Separation Induced by a Model Vocal Fold Polyp09:58

Investigating the Three-dimensional Flow Separation Induced by a Model Vocal Fold Polyp

Published on: February 3, 2014

8.7K

Related Concept Videos

Single Pipe Systems01:24

Single Pipe Systems

In pipe flow analysis, problems are typically categorized into three types — Type I, Type II, and Type III — based on the known parameters and the desired outcome. Each type of problem addresses specific engineering requirements using fluid properties, pipe characteristics, and operational conditions.
In a Type I problem, fluid properties (density and viscosity), pipe characteristics (including diameter, length, and surface roughness), and the flow rate or average velocity are...
338
General Characteristics of Pipe Flow I01:22

General Characteristics of Pipe Flow I

Pipe flow refers to the movement of fluids within fully enclosed conduits, typically cylindrical in shape, such as water pipes or hydraulic hoses. These conduits are designed to withstand high-pressure gradients that drive fluid movement, contrasting with open-channel flows, where gravity is the primary driving force. Rectangular conduits, like air conditioning and heating ducts, generally operate at lower pressures and are less suited for high-pressure applications.
The classification of fluid...
1.6K
Laminar Flow: Problem Solving01:24

Laminar Flow: Problem Solving

Laminar flow occurs when a fluid moves smoothly in parallel layers with minimal mixing and turbulence. In fluid mechanics, ensuring laminar flow within a pipe is essential for precise control of flow characteristics, especially in engineering applications. The key factor in determining whether flow remains laminar is the Reynolds number, a dimensionless quantity that depends on the fluid's velocity, density, viscosity, and the pipe's diameter. A Reynolds number of 2100 or lower...
409
General Characteristics of Pipe Flow II01:24

General Characteristics of Pipe Flow II

When fluid enters a pipe, it first passes through the entrance region, where the velocity profile adjusts due to viscous effects. In this region, a boundary layer forms along the pipe walls and grows until it fully occupies the pipe's cross-section. Once the boundary layer merges, the flow becomes fully developed, with a steady velocity profile that remains consistent along the pipe's length.
The distance to reach a fully developed flow is called the entrance length and depends on the...
1.5K
Laminar Flow01:27

Laminar Flow

Laminar flow represents a smooth, orderly fluid motion where particles move along parallel paths, resulting in minimal mixing between layers. Streamlined particle paths characterize this flow regime and occur under conditions where viscous forces dominate over inertial forces. The distinction between laminar, transitional, and turbulent flow is primarily determined by the Reynolds number, a dimensionless quantity calculated as:
1.9K
Major Losses in Pipes01:28

Major Losses in Pipes

When a fluid flows through a pipe, it experiences energy losses due to frictional resistance along the pipe walls, known as major losses. These energy losses result in a pressure drop, which varies based on the flow conditions — whether laminar or turbulent — and the specific physical properties of the fluid and pipe.
Fluid flow can be classified as laminar or turbulent, primarily based on the Reynolds number. This dimensionless number reflects the relative influence of inertial to viscous...
1.7K