Related Experiment Video

Updated: Dec 11, 2025

20 mJ, 1 ps Yb:YAG Thin-disk Regenerative Amplifier
10:17

20 mJ, 1 ps Yb:YAG Thin-disk Regenerative Amplifier

Published on: July 12, 2017

11.9K

Comparison of multi-pass and regenerative strategies for energetic high-gain amplifiers based on Yb:CaF2

Frédéric Druon, Kévin Genevrier, Patrick Georges

    Optics Letters
    |August 16, 2020
    PubMed

    More Related Videos

    High-speed Continuous-wave Stimulated Brillouin Scattering Spectrometer for Material Analysis07:55

    High-speed Continuous-wave Stimulated Brillouin Scattering Spectrometer for Material Analysis

    Published on: September 22, 2017

    10.5K
    Generation and Coherent Control of Pulsed Quantum Frequency Combs06:42

    Generation and Coherent Control of Pulsed Quantum Frequency Combs

    Published on: June 8, 2018

    9.5K

    Related Concept Videos

    BJT Amplifiers01:14

    BJT Amplifiers

    Bipolar Junction Transistors (BJTs) are pivotal components in amplifier circuits, functioning as voltage-controlled current sources in their active region. This characteristic allows them to efficiently control the collector current through variations in the base-emitter voltage. Essentially, BJTs amplify power due to their ability to take a weak input signal and output a much stronger signal.
    In BJT amplifier configurations, particularly in common-emitter setups, the transistor's role...
    838
    Cascaded Op Amps01:16

    Cascaded Op Amps

    Operational amplifiers (op-amps) are versatile electronic components that can be interconnected in a cascade - one after another in a linear sequence. This cascading is possible due to their infinite input resistance and zero output resistance, allowing them to maintain their input-output relationships even when connected in series.
    In a cascaded system, each op-amp is referred to as a stage. The output of one stage drives the input of the subsequent stage. As the input signal passes through...
    966
    Small-Signal Analysis of BJT Amplifiers01:21

    Small-Signal Analysis of BJT Amplifiers

    Small signal analysis is a fundamental approach used in electronics to understand how a Bipolar Junction Transistor (BJT) amplifier processes signals. In the active region, the BJT is designed for linear amplification. The transistor's behavior under these conditions is governed by its instantaneous base-emitter voltage VBE, a sum of the DC bias VBE, and a small AC signal VBE, resulting in the collector current iC. Here, the collector current has a DC component and an AC component.
    1.5K
    MOSFET Amplifiers01:17

    MOSFET Amplifiers

    The MOSFET, when operating in its active region, functions as a voltage-controlled current source. In this region, the gate-to-source voltage controls the drain current. This principle underlies the operation of the transconductance MOSFET amplifier. The output current is directed through a load resistor to convert this amplifier into a voltage amplifier. The output voltage is then obtained by subtracting the voltage drop across the load resistance from the supply voltage. This process results...
    375
    Design Example: Capacitance Multiplier Circuit01:20

    Design Example: Capacitance Multiplier Circuit

    In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
    The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
    1.3K
    Small-Signal Analysis of MOSFET Amplifiers01:23

    Small-Signal Analysis of MOSFET Amplifiers

    In small-signal analysis, a MOSFET transistor amplifier acts as a linear amplifier when operating in its saturation region. The gate-to-source voltage (VGS) of the MOSFET is the sum of the DC biasing voltage and the small time-varying input signal. This combination sets up the operating point and modulates the drain current (ID) that flows from the drain to the source. When a small AC signal is superimposed on the DC bias voltage at the gate, the instantaneous drain current comprises three...
    956