Related Experiment Video

Updated: Dec 10, 2025

Large Scale Energy Efficient Sensor Network Routing Using a Quantum Processor Unit
05:30

Large Scale Energy Efficient Sensor Network Routing Using a Quantum Processor Unit

Published on: September 8, 2023

971

Energy Consumption Analysis of LPWAN Technologies and Lifetime Estimation for IoT Application

Ritesh Kumar Singh1, Priyesh Pappinisseri Puluckul1, Rafael Berkvens1

  • 1IDLab-Faculty of Applied Engineering, University of Antwerp-imec, Sint-Pietersvliet 7, 2000 Antwerp, Belgium.

Sensors (Basel, Switzerland)
|August 29, 2020
PubMed

Keywords:
DASH7LPWANLoRaWANNB-IoTSigfoxenergy efficiencypower consumption

More Related Videos

Setup of Consumer Wearable Devices for Exposure and Health Monitoring in Population Studies15:00

Setup of Consumer Wearable Devices for Exposure and Health Monitoring in Population Studies

Published on: February 3, 2023

2.8K
Field Measurement of Effective Leaf Area Index using Optical Device in Vegetation Canopy06:28

Field Measurement of Effective Leaf Area Index using Optical Device in Vegetation Canopy

Published on: July 29, 2021

3.7K

Related Concept Videos

Electrical Energy01:10

Electrical Energy

Using electric appliances for a longer period of time consumes more electrical energy and results in a higher electric bill. The energy produced by the transfer of electrons from one point to another is known as electrical energy. If power is delivered at a constant rate, the electrical energy can be defined as the product of power used by the device for a period of time. The energy unit on electric bills is the kilowatt-hour, where one kilowatt-hour is equivalent to 3.6 × 106 joules.
1.6K
Energy and Power Signals01:17

Energy and Power Signals

In an electrical system with a resistor, voltage and current signals facilitate the measurement of power and energy across the resistor. For a continuous-time signal, the total energy over a time interval is defined as the integral of the square of the signal's magnitude over that interval. Mathematically, this is expressed as:
950
Energy Budgets00:51

Energy Budgets

Organisms must balance energy intake with the energy required for growth, maintenance and reproduction. These trade-offs result in a variety of survivorship and reproductive strategies, including semelparity and iteroparity. Semelparous species, like annual plants, have only one reproductive episode in their lifetimes and consequently have short lifespans. Iteroparous species, by contrast, have many reproductive events during their lifetimes but have relatively few offspring. These two...
10.4K
Laminar Flow01:27

Laminar Flow

Laminar flow represents a smooth, orderly fluid motion where particles move along parallel paths, resulting in minimal mixing between layers. Streamlined particle paths characterize this flow regime and occur under conditions where viscous forces dominate over inertial forces. The distinction between laminar, transitional, and turbulent flow is primarily determined by the Reynolds number, a dimensionless quantity calculated as:
1.9K
Maximum Power Flow and Line Loadability01:23

Maximum Power Flow and Line Loadability

The maximum power flow for lossy transmission lines is derived using ABCD parameters in phasor form. These parameters create a matrix relationship between the sending-end and receiving-end voltages and currents, allowing the determination of the receiving-end current. This relationship facilitates calculating the complex power delivered to the receiving end, from which real and reactive power components are derived.
502
Energy Losses in Transformers01:21

Energy Losses in Transformers

In an ideal transformer, it is assumed that there are no energy losses, and, hence, all the power at the primary winding is transferred to the secondary winding. However, in reality,  the transformers always have some energy losses, and, hence, the output power obtained at the secondary winding is less than the input power at the primary winding due to energy losses.
There are four main reasons for energy losses in transformers.
The first cause can be  the high resistance of the...
1.2K