Related Experiment Video

Updated: Dec 8, 2025

Combustion Chemistry of Fuels: Quantitative Speciation Data Obtained from an Atmospheric High-temperature Flow Reactor with Coupled Molecular-beam Mass Spectrometer

Combustion Chemistry of Fuels: Quantitative Speciation Data Obtained from an Atmospheric High-temperature Flow Reactor with Coupled Molecular-beam Mass Spectrometer

Published on: February 19, 2018

Presenting a Four-Lump Dynamic Kinetic Model for Methanol to Light Olefins Process Over the Hierarchical SAPO-34

Mohammad Javad Azarhoosh¹, Ali Reza Azarhoosh²

¹Chemical Engineering Department, Urmia University, Urmia, Iran.

Combinatorial Chemistry & High Throughput Screening

|September 16, 2020

Abstract

Objectives:

A four-lump dynamic kinetic model on the hierarchical SAPO-34 catalyst in the methanol to light olefins (MTO) process has been presented using the power law models. Since decreased catalyst activity in the MTO process is common, for the applicability of the proposed model, the function of catalyst activity was computed as a function of the coke percentage deposited on the catalyst.

Materials And Methods:

The reactant and products were divided into four lumps, including methanol and dimethyl ether (DME), light olefins (ethylene and propylene), light paraffin (methane, ethane, and propane) and heavier hydrocarbons from C4. The one-dimensional ideal plug reactor was used for the simulation of the MTO reactor. The kinetic parameters and the catalyst activity function were predicted using the particle swarm optimization (PSO) algorithm.

Results:

The comparison of product distribution in the experimental model and the results of the kinetic model indicated the high accuracy of the presented model. The effect of operational parameters such as temperature and weight hourly space velocity (WHSV) on the mole percent of light olefins was investigated using the proposed kinetic model. The optimized value of temperature and WHSV to reach the maximum yield of light olefins was respectively 460 ˚C and 4.2 h^-1.

Conclusion:

The passive kinetic coefficients were estimated in the reaction rate constant and catalyst activity function with the help of the PSO optimization algorithm. The mole fraction of different products and the reactant arising from modeling at the reactor outlet was compared with experimental results, which indicated the high accuracy of the presented kinetic model. The results also revealed that the selection of high and low temperatures and WHSV decreases the yield of light olefins and the lifetime of the catalyst.

Keywords:

Kinetic study MTO process SAPO-34 hierarchical catalyst lump modeling petrochemical industries

More Related Videos

Optimize Flue Gas Settings to Promote Microalgae Growth in Photobioreactors via Computer Simulations

Optimize Flue Gas Settings to Promote Microalgae Growth in Photobioreactors via Computer Simulations

Published on: October 1, 2013

Multiscale Sampling of a Heterogeneous Water/Metal Catalyst Interface using Density Functional Theory and Force-Field Molecular Dynamics

Multiscale Sampling of a Heterogeneous Water/Metal Catalyst Interface using Density Functional Theory and Force-Field Molecular Dynamics

Published on: April 12, 2019

Related Concept Videos

Catalysis

Catalysis

The presence of a catalyst affects the rate of a chemical reaction. A catalyst is a substance that can increase the reaction rate without being consumed during the process. A basic comprehension of a catalysts’ role during chemical reactions can be understood from the concept of reaction mechanisms and energy diagrams.

Electrophilic Addition of HX to 1,3-Butadiene: Thermodynamic vs Kinetic Control

Electrophilic Addition of HX to 1,3-Butadiene: Thermodynamic vs Kinetic Control

The addition of a hydrogen halide to 1,3-butadiene gives a mixture of 1,2- and 1,4-adducts. Since more substituted alkenes are more stable, the 1,4-adduct is expected to be the major product. However, the product distribution is strongly influenced by temperature; low temperature favors the 1,2-adduct, whereas the 1,4-adduct is predominant at high temperature.

Turnover Number and Catalytic Efficiency

Turnover Number and Catalytic Efficiency

The turnover number of an enzyme is the maximum number of substrate molecules it can transform per unit time. Turnover numbers for most enzymes range from 1 to 1000 molecules per second. Catalase has the known highest turnover number, capable of converting up to 2.8×106 molecules of hydrogen peroxide into water and oxygen per second. Lysozyme has the lowest known turnover number of half a molecule per second.
Chymotrypsin is a pancreatic enzyme that breaks down proteins during digestion....

Benzene to Phenol via Cumene: Hock Process

Benzene to Phenol via Cumene: Hock Process

The synthesis of phenol from benzene via cumene and cumene hydroperoxide is called the Hock process. First, a Friedel–Crafts alkylation reaction of benzene with propene gives cumene. Then cumene forms cumene hydroperoxide via a radical chain reaction. In the chain initiation step, the benzylic hydrogen is abstracted to give a benzylic radical. In the chain propagation step, the benzylic radical reacts with an oxygen diradical to form a cumene hydroperoxide radical. The cumene...

Factors Affecting Activity Coefficient

Factors Affecting Activity Coefficient

The extended Debye-Hückel equation indicates that the activity coefficient of an ion in an aqueous solution at 25°C depends on three partially interdependent properties: the ionic strength of the solution, the charge of the ion, and the ion size.
The activity coefficient value for an ion is close to one when the solution has almost zero ionic strength, i.e., when the solution shows close to ideal behavior. As the ionic strength of the solution increases from 0 to 0.1 mol/L, a...

Combustion Energy: A Measure of Stability in Alkanes and Cycloalkanes

Combustion Energy: A Measure of Stability in Alkanes and Cycloalkanes

The low reactivity in alkanes can be attributed to the non-polar nature of C–C and C–H σ bonds. Alkanes, therefore, were initially termed as “paraffins,” derived from the Latin words: parum, meaning “too little,” and affinis, meaning “affinity.”
Alkanes undergo combustion in the presence of excess oxygen and high-temperature conditions to give carbon dioxide and water. A combustion reaction is the energy source in natural gas, liquified...

Articles linked to this work by shared authors, journal, and citation graph.

Thermodynamic assessment of tri-reforming of methane with optimization of operating conditions to achieve suitable syngas for methanol production.

Scientific reports·2026

Urease production using corn steep liquor as a low-cost nutrient source by Sporosarcina pasteurii: biocementation and process optimization via artificial intelligence approaches.

Environmental science and pollution research international·2021

Performance analysis of ultrasound-assisted synthesized nano-hierarchical SAPO-34 catalyst in the methanol-to-lights-olefins process via artificial intelligence methods.

Ultrasonics sonochemistry·2019

Presenting a new kinetic model for methanol to light olefins reactions over a hierarchical SAPO-34 catalyst using the Langmuir-Hinshelwood-Hougen-Watson mechanism.

Journal of physics. Condensed matter : an Institute of Physics journal·2017

See all related articles