Related Experiment Video

Updated: Nov 30, 2025

Ultrahigh Density Array of Vertically Aligned Small-molecular Organic Nanowires on Arbitrary Substrates
08:07

Ultrahigh Density Array of Vertically Aligned Small-molecular Organic Nanowires on Arbitrary Substrates

Published on: June 18, 2013

15.4K

Sequential Doping of Ladder-Type Conjugated Polymers for Thermally Stable n-Type Organic Conductors

Suhao Wang1, Tero-Petri Ruoko1, Gang Wang1

  • 1Laboratory of Organic Electronics, Department of Science and Technology, Linköping University, 60174 Norrköping, Sweden.

ACS Applied Materials & Interfaces
|November 12, 2020
PubMed

Keywords:
conjugated polymersladder-type polymersn-dopingorganic thermoelectricssequential dopingthermal stability

More Related Videos

Morphology Control for Fully Printable Organic–Inorganic Bulk-heterojunction Solar Cells Based on a Ti-alkoxide and Semiconducting Polymer08:29

Morphology Control for Fully Printable Organic–Inorganic Bulk-heterojunction Solar Cells Based on a Ti-alkoxide and Semiconducting Polymer

Published on: January 10, 2017

9.3K
Electroactive Polymer Nanoparticles Exhibiting Photothermal Properties10:16

Electroactive Polymer Nanoparticles Exhibiting Photothermal Properties

Published on: January 8, 2016

14.2K

Related Concept Videos

Ziegler–Natta Chain-Growth Polymerization: Overview01:17

Ziegler–Natta Chain-Growth Polymerization: Overview

Ziegler–Natta polymerization is another form of addition or chain‐growth polymerization used for synthesizing linear polymers over branched polymers. The catalyst used for polymerization is the Ziegler–Natta catalyst, named after Karl Ziegler and Giulio Natta, who developed it in 1953. This catalyst is an organometallic complex of titanium tetrachloride and triethyl aluminum, with the active form of the catalyst being an alkyl titanium compound. Using the Ziegler–Natta...
3.7K
[4+2] Cycloaddition of Conjugated Dienes: Diels–Alder Reaction01:16

[4+2] Cycloaddition of Conjugated Dienes: Diels–Alder Reaction

The Diels–Alder reaction is an example of a thermal pericyclic reaction between a conjugated diene and an alkene or alkyne, commonly referred to as a dienophile. The reaction involves a concerted movement of six π electrons, four from the diene and two from the dienophile, forming an unsaturated six-membered ring. As a result, these reactions are classified as [4+2] cycloadditions.
11.6K
Stability of Conjugated Dienes01:28

Stability of Conjugated Dienes

Introduction
A comparison of the enthalpies of hydrogenation of dienes reveals that conjugated dienes release less heat on hydrogenation, rendering them more stable than their nonconjugated analogs.
3.9K
Step-Growth Polymerization: Overview01:03

Step-Growth Polymerization: Overview

Step-growth or condensation polymerization is a stepwise reaction of bi or multifunctional monomers to form long-chain polymers. As all the monomers are reactive, most of the monomers are consumed at the early stages of the reaction to form small chains of reactive oligomers, which then combine to form long polymer chains in the late stages. Hence, the reaction has to proceed for a long time to achieve high molecular weight polymers.
Many natural and synthetic polymers are produced by...
4.1K
Thermal Electrocyclic Reactions: Stereochemistry01:17

Thermal Electrocyclic Reactions: Stereochemistry

The stereochemistry of electrocyclic reactions is strongly influenced by the orbital symmetry of the polyene HOMO. Under thermal conditions, the reaction proceeds via the ground-state HOMO.
Selection Rules: Thermal Activation
Conjugated systems containing an even number of π-electron pairs undergo a conrotatory ring closure. For example, thermal electrocyclization of (2E,4E)-2,4-hexadiene, a conjugated diene containing two π-electron pairs, gives trans-3,4-dimethylcyclobutene.
2.3K
Cycloaddition Reactions: MO Requirements for Thermal Activation01:16

Cycloaddition Reactions: MO Requirements for Thermal Activation

Thermal cycloadditions are reactions where the source of activation energy needed to initiate the reaction is provided in the form of heat. A typical example of a thermally-allowed cycloaddition is the Diels–Alder reaction, which is a [4 + 2] cycloaddition. In contrast, a [2 + 2] cycloaddition is thermally forbidden.
4.0K