Related Experiment Video

Updated: Nov 25, 2025

Use of Galvanic Skin Responses, Salivary Biomarkers, and Self-reports to Assess Undergraduate Student Performance During a Laboratory Exam Activity
07:32

Use of Galvanic Skin Responses, Salivary Biomarkers, and Self-reports to Assess Undergraduate Student Performance During a Laboratory Exam Activity

Published on: February 10, 2016

9.6K

Determinants of academic stress amongst engineering students

Anurag Joshi1, Ravi Kiran2

  • 1Department of Electrical Engineering, Thapar Polytechnic College, Punjab, India.

Work (Reading, Mass.)
|December 16, 2020
PubMed
Abstract

Keywords:
Genderageengineering streamsnature of universitiesquestionnaire

More Related Videos

Evaluation of Commercial-Off-The-Shelf Wrist Wearables to Estimate Stress on Students12:51

Evaluation of Commercial-Off-The-Shelf Wrist Wearables to Estimate Stress on Students

Published on: June 16, 2018

7.7K
A Cross-Disciplinary and Multi-Modal Experimental Design for Studying Near-Real-Time Authentic Examination Experiences08:33

A Cross-Disciplinary and Multi-Modal Experimental Design for Studying Near-Real-Time Authentic Examination Experiences

Published on: September 4, 2019

7.3K

Related Concept Videos

Principal Stresses: Problem Solving01:15

Principal Stresses: Problem Solving

When analyzing two planes intersecting at right angles under the influence of shearing, tensile, and compressive stresses, it is essential to identify principal planes, maximum shearing stress, and principal stresses. To find the principal planes, apply a formula that equates them to twice the shearing stress divided by the difference between tensile and compressive stresses.
415
Stress Concentrations01:13

Stress Concentrations

The concept of stress concentration is crucial for understanding how materials respond under bending stresses, particularly when there are irregularities or discontinuities in the material's geometry. Normally, stress in a symmetric member subjected to pure bending is assumed to be uniformly distributed across the entire cross-section. However, this assumption does not hold when there are variations in the cross-sectional geometry or the presence of notches and holes.
The stress...
450
Stress Concentrations01:24

Stress Concentrations

Stress concentration is when stress intensifies near discontinuities such as holes or abrupt cross-sectional changes in a structural member. This localized stress can often surpass the average stress within the member. The stress distribution in flat bars, either with a circular hole or varying widths connected by fillets, can be determined experimentally using a photoelastic method. The results are based on ratios of geometric parameters like the ratio of the hole's radius to the smaller...
500
True Stress and True Strain01:28

True Stress and True Strain

Engineering stress is calculated as the load divided by the original, undeformed cross-sectional area. It approximates a material under load. This approximation is especially relevant post-yield in ductile materials. Though engineering stress-strain diagrams are often used for their convenience and accessibility, they can sometimes fall short in accuracy, particularly when dealing with large strain values.
In contrast, true stress offers a more precise portrayal. It is computed by dividing the...
602
General State of Stress01:21

General State of Stress

The general state of stress within a material can be accurately depicted using a stress tensor. This tensor encapsulates the internal forces distributed within a material subjected to external forces or deformations.
Specifically, consider a tetrahedral element where one face, labeled XYZ, is perpendicular to the line OA, and the remaining faces align with the coordinate axes with point O as the origin. At any point, such as point O, the stress tensor can be used to determine the stress...
457
Bearing Stress01:22

Bearing Stress

Bearing stress refers to the contact pressure between two separate bodies. To visualize this, imagine a bolt thrust through a plate. The bolt applies a force to the plate, which exerts an equal but opposite force back onto the bolt. This force isn't just a singular entity but a compilation of numerous smaller forces distributed across the contact surface between the bolt and the plate.
Due to the intricacy of these microforces, an average value, known as bearing stress, is often used by...
1.5K