Related Experiment Video

Updated: Nov 18, 2025

Use of a Foot-Induced Digitally Controlled Resistance Device for Functional Magnetic Resonance Imaging Evaluation in Patients with Foot Paresis
08:55

Use of a Foot-Induced Digitally Controlled Resistance Device for Functional Magnetic Resonance Imaging Evaluation in Patients with Foot Paresis

Published on: July 7, 2023

490

Physical demands associated with right-angle direct-current power-tools: An evaluation of current technology

C Steingraber1, D Devries1, L Eaton2

  • 1Department of Kinesiology, University of Windsor, Windsor, ON, Canada.

Applied Ergonomics
|February 5, 2021
PubMed

Keywords:
Manufacturing ergonomicsPhysical demandsRight-angle power tool

More Related Videos

Determining and Controlling External Power Output During Regular Handrim Wheelchair Propulsion08:55

Determining and Controlling External Power Output During Regular Handrim Wheelchair Propulsion

Published on: February 5, 2020

7.8K
Measurement of the Hand Transmitted Vibration of the Human Hand Arm System During Operation of a Hand Tractor09:35

Measurement of the Hand Transmitted Vibration of the Human Hand Arm System During Operation of a Hand Tractor

Published on: June 16, 2021

4.7K

Related Concept Videos

Power in a Three-Phase Circuit01:15

Power in a Three-Phase Circuit

Three-phase systems have two configurations: the wye and delta. A star configuration can be three or four wires; in a delta configuration, the components are connected in a closed loop. Instantaneous power refers to the power value at a precise moment, and in a balanced three-phase system, it is constant. This is because the sum of the instantaneous powers in the three phases remains steady over time, despite individual fluctuations, due to the symmetry and phase relationship. The total...
491
Three-Phase Short Circuit—Unloaded Synchronous Machine01:21

Three-Phase Short Circuit—Unloaded Synchronous Machine

Conducting a three-phase short circuit test on an unloaded synchronous machine helps understand its impact on the system. The AC fault current's oscillogram, with the DC offset removed, reveals that the waveform amplitude decreases from an initially high value to a steady-state level for one phase of the machine.
This behavior occurs due to the magnetic flux produced by the short-circuit armature currents. Initially, these currents follow high-reluctance paths but eventually shift to...
508
AC Sources01:20

AC Sources

Direct current is a flow of electric charge in only one direction and has a steady state of constant voltage in the circuit. Rectifiers, batteries, commutator-equipped generators, and fuel cells are some examples of devices that generate direct current. Nowadays, most applications use a time-varying voltage source. Alternating current is a flow of electric charge that periodically reverses direction. An alternating current is produced by an alternating emf that is generated in a power plant. If...
3.5K
Directional Relays01:25

Directional Relays

Directional relays, essential for managing unidirectional fault currents, enhance the safety and efficiency of power systems. On power lines equipped with directional relays, faults downstream (to the right) of the current transformer typically cause the fault current to lag the bus voltage by approximately 90 degrees, known as the forward direction. In contrast, upstream (left-side) faults may result in the fault current leading the bus voltage by nearly 90 degrees, termed the reverse...
430
Force On A Current Loop In A Magnetic Field01:17

Force On A Current Loop In A Magnetic Field

Magnetic forces on wires carrying current are most frequently applied in motors. A DC motor is a device that converts electrical energy into mechanical work. In motors, wire loops are enclosed in a magnetic field. When current flows through the loops, the magnetic field applies torque, which causes the shaft to rotate. The direction of the current is reversed once the loop's surface area is lined up with the magnetic field, causing a constant torque on the loop. During the process, commutators...
3.7K
Machines01:19

Machines

Machines are complex structures consisting of movable, pin-connected multi-force members that work together to transmit forces. One example of a machine is the cutting plier, which is used to cut wires by applying forces to its handles. When equal and opposite forces are exerted on the handles of the cutting plier, they cause the cutting edges to come together and apply equal and opposite reaction forces on the wire, which are greater than the applied forces.
A free-body diagram of the...
455