Related Experiment Video

Updated: Nov 16, 2025

Method to Measure Tone of Axial and Proximal Muscle
10:41

Method to Measure Tone of Axial and Proximal Muscle

Published on: December 14, 2011

17.8K

Comparison of the Torsional Resistance of 4 Different Glide Path Instruments

Özlem Sivas Yilmaz1, Cangül Keskin2, Hikmet Aydemir2

  • 1Department of Endodontics, Faculty of Dentistry, Karabuk University, Karabuk, Turkey.

Journal of Endodontics
|February 28, 2021
PubMed
Abstract

Keywords:
Glide pathRotatenickel-titaniumtorsional strength

More Related Videos

A Probing Device for Quantitatively Measuring the Mechanical Properties of Soft Tissues during Arthroscopy06:16

A Probing Device for Quantitatively Measuring the Mechanical Properties of Soft Tissues during Arthroscopy

Published on: May 1, 2020

5.7K
A Simple Flight Mill for the Study of Tethered Flight in Insects07:42

A Simple Flight Mill for the Study of Tethered Flight in Insects

Published on: December 10, 2015

17.5K

Related Concept Videos

Torsional Pendulum01:09

Torsional Pendulum

A torsional pendulum involves the oscillation of a rigid body in which the restoring force is provided by the torsion in the string from which the rigid body is suspended. Ideally, the string should be massless; practically, its mass is much smaller than the rigid body's mass and is neglected.
As long as the rigid body's angular displacement is small, its oscillation can be modeled as a linear angular oscillation. The amplitude of the oscillation is an angle. The role of mass is played...
6.5K
Bending and Torsional Moments01:20

Bending and Torsional Moments

Bending and torsional moments are two fundamental concepts in structural engineering. They play an important role in understanding the behavior of materials and structures under different loading conditions.
The reaction developed in a structural element when subjected to an external force causes the element to bend. When a structural element bends upwards, it creates compressive normal forces on the top and tensile normal forces on the bottom, resulting in a couple that determines the bending...
4.9K
Gyroscope: Precession01:24

Gyroscope: Precession

Precession can be demonstrated effectively through a spinning top. If a spinning top is placed on a flat surface near the surface of the Earth at a vertical angle and is not spinning, it will fall over due to the force of gravity producing a torque acting on its center of mass. However, if the top is spinning on its axis, it precesses about the vertical direction, rather than topple over due to this torque. Precessional motion is a combination of a steady circular motion of the axis and the...
4.8K
Angle of Twist - Elastic Range01:13

Angle of Twist - Elastic Range

Consider a cylindrical shaft with a length denoted by L and a consistent cross-sectional radius referred to as r. This shaft undergoes a torque at the free end. The highest shearing strain within the shaft is directly proportional to the twist angle and the radial distance from the shaft axis. When the shaft behaves elastically, this shearing strain can be articulated using variables such as the applied torque, radial distance, the polar moment of inertia, and the modulus of rigidity. By...
541
Gyroscope01:02

Gyroscope

A gyroscope is defined as a spinning disk in which the axis of rotation is free to assume any orientation. When spinning, the orientation of the spin axis is unaffected by the orientation of the body that encloses it. The body or vehicle enclosing the gyroscope can be moved from place to place, while the orientation of the spin axis remains the same. This makes gyroscopes very useful in navigation, especially where magnetic compasses cannot be used, such as in crewed and crewless spacecraft,...
3.6K
Deformation in a Circular Shaft01:10

Deformation in a Circular Shaft

One of the distinctive characteristics of circular shafts is their ability to maintain their cross-sectional integrity under torsion. In other words, each cross-section continues to exist as a flat, unaltered entity, simply rotating like a solid, rigid slab. To understand the distribution of shearing stress within such a shaft, consider a cylindrical section inside this circular shaft. This section has a length of L and a radius of R, with one end fixed. The radius of the cylindrical section is...
606