Related Experiment Video

Updated: Nov 15, 2025

Experimental Investigation of the Hierarchical Control in DC Microgrids Using a Real-time Simulator
06:04

Experimental Investigation of the Hierarchical Control in DC Microgrids Using a Real-time Simulator

Published on: February 14, 2025

794

Stability of Time-Varying Hybrid Stochastic Delayed Systems With Application to Aperiodically Intermittent

Pengfei Wang, Ruifang Wang, Huan Su

    IEEE Transactions on Cybernetics
    |March 4, 2021
    PubMed

    More Related Videos

    Bouncing Ball with a Uniformly Varying Velocity in a Metronome Synchronization Task05:04

    Bouncing Ball with a Uniformly Varying Velocity in a Metronome Synchronization Task

    Published on: September 21, 2017

    6.2K
    A Method for Tracking the Time Evolution of Steady-State Evoked Potentials12:03

    A Method for Tracking the Time Evolution of Steady-State Evoked Potentials

    Published on: May 25, 2019

    8.7K

    Related Concept Videos

    Stability01:28

    Stability

    The time response of a linear time-invariant (LTI) system can be divided into transient and steady-state responses. The transient response represents the system's initial reaction to a change in input and diminishes to zero over time. In contrast, the steady-state response is the behavior that persists after the transient effects have faded.
    The stability of an LTI system is determined by the roots of its characteristic equation, known as poles. A system is stable if it produces a bounded...
    237
    BIBO stability of continuous and discrete -time systems01:24

    BIBO stability of continuous and discrete -time systems

    System stability is a fundamental concept in signal processing, often assessed using convolution. For a system to be considered bounded-input bounded-output (BIBO) stable, any bounded input signal must produce a bounded output signal. A bounded input signal is one where the modulus does not exceed a certain constant at any point in time.
    To determine the BIBO stability, the convolution integral is utilized when a bounded continuous-time input is applied to a Linear Time-Invariant (LTI) system....
    724
    Classification of Systems-II01:31

    Classification of Systems-II

    Continuous-time systems have continuous input and output signals, with time measured continuously. These systems are generally defined by differential or algebraic equations. For instance, in an RC circuit, the relationship between input and output voltage is expressed through a differential equation derived from Ohm's law and the capacitor relation,
    345
    Linear Approximation in Time Domain01:21

    Linear Approximation in Time Domain

    Nonlinear systems often require sophisticated approaches for accurate modeling and analysis, with state-space representation being particularly effective. This method is especially useful for systems where variables and parameters vary with time or operating conditions, such as in a simple pendulum or a translational mechanical system with nonlinear springs.
    For a simple pendulum with a mass evenly distributed along its length and the center of mass located at half the pendulum's length,...
    197
    Multimachine Stability01:25

    Multimachine Stability

    Multimachine stability analysis is crucial for understanding the dynamics and stability of power systems with multiple synchronous machines. The objective is to solve the swing equations for a network of M machines connected to an N-bus power system.
    In analyzing the system, the nodal equations represent the relationship between bus voltages, machine voltages, and machine currents. The nodal equation is given by:
    291
    Time-Domain Interpretation of PD Control01:07

    Time-Domain Interpretation of PD Control

    Proportional-Derivative (PD) control is a widely used control method in various engineering systems to enhance stability and performance. In a system with only proportional control, common issues include high maximum overshoot and oscillation, observed in both the error signal and its rate of change. This behavior can be divided into three distinct phases: initial overshoot, subsequent undershoot, and gradual stabilization.
    Consider the example of control of motor torque. Initially, a positive...
    236