Related Experiment Video

Updated: Nov 5, 2025

Microfluidic Fabrication of Polymeric and Biohybrid Fibers with Predesigned Size and Shape
07:38

Microfluidic Fabrication of Polymeric and Biohybrid Fibers with Predesigned Size and Shape

Published on: January 8, 2014

8.7K

Design of steering wheel-type ring depressed-core 10-mode fiber with fully improved mode spacing

Yuheng Xie, Li Pei, Jingjing Zheng

    Optics Express
    |May 14, 2021
    PubMed

    More Related Videos

    Writing Bragg Gratings in Multicore Fibers08:48

    Writing Bragg Gratings in Multicore Fibers

    Published on: April 20, 2016

    8.3K
    Prescribed 3-D Direct Writing of Suspended Micron/Sub-micron Scale Fiber Structures via a Robotic Dispensing System10:36

    Prescribed 3-D Direct Writing of Suspended Micron/Sub-micron Scale Fiber Structures via a Robotic Dispensing System

    Published on: June 12, 2015

    8.2K

    Related Concept Videos

    Design of Transmission Shafts01:16

    Design of Transmission Shafts

    The design of a transmission shaft is governed by two primary specifications: the power it transmits and its rotational speed. These parameters guide the selection of the shaft's material and cross-sectional dimensions, ensuring that the material's maximum shearing stress remains within the elastic limit while transmitting the desired power at the given speed. The system's power is intrinsically linked to the applied torque. The torque applied to the shaft can be calculated by reconfiguring the...
    556
    Fiber Reinforced Concrete01:22

    Fiber Reinforced Concrete

    Fiber-reinforced concrete significantly enhances the structural and nonstructural properties of traditional concrete by incorporating fibers like steel, glass, and polymers. These fibers, varying from natural ones such as sisal and cellulose to manufactured ones like polypropylene and Kevlar, are mixed into hydraulic cement with aggregates. Steel fibers, often preferred for their robustness, contribute to improved ductility, toughness, and post-cracking performance. The concrete is classified...
    179
    PD Controller: Design01:26

    PD Controller: Design

    In automotive engineering, car suspension systems often employ Proportional Derivative (PD) controllers to enhance performance. PD controllers are utilized to adjust the damping force in response to road conditions. A controller, acting as an amplifier with a constant gain, demonstrates proportional control, with output directly mirroring input.
    Designing a continuous-data controller requires selecting and linking components like adders and integrators, which are fundamental in Proportional,...
    430
    Design of Transmission Shafts - Stress Analysis01:15

    Design of Transmission Shafts - Stress Analysis

    Designing a transmission shaft requires a thorough understanding of the stresses induced by bending moments and torques, especially in systems where power is transferred through gears. These forces create force-couple systems at the centers of the shaft's cross-sections, leading to both transverse and torsional loading. Although shearing stresses from transverse loads are typically smaller than those from torques and are often overlooked, the significant normal stresses from these loads...
    561
    Design Example: Calculating Safe Diameter for Wind-Exposed Disc01:17

    Design Example: Calculating Safe Diameter for Wind-Exposed Disc

    Assessing safety in wind-exposed installations is crucial to preventing potential failures. This example explores the calculation and design adjustments needed to mount a circular disc on a building facade, where wind forces are a primary concern. A 4-meter diameter disc was initially designed as an aesthetic feature facing winds at a velocity of 25 meters per second, with an air density of 1.25 kilograms per cubic meter. Given these conditions, the drag force on the disc was determined using...
    216
    Thin-Walled Hollow Shafts01:15

    Thin-Walled Hollow Shafts

    In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution of...
    332