Correction: Exploring secondary interactions and the role of temperature in moisture-contaminated polymer networks
Rishabh D Guha1, Ogheneovo Idolor1, Katherine Berkowitz1
1Department of Mechanical and Aerospace Engineering, North Carolina State University, Engineering Building-III, 911 Oval Drive, Raleigh, NC-27695, USA. lgrace2@ncsu.edu.
Soft Matter
|May 28, 2021
Abstract:
Correction for 'Exploring secondary interactions and the role of temperature in moisture-contaminated polymer networks through molecular simulations' by Rishabh D. Guha et al., Soft Matter, 2021, 17, 2942-2956, DOI: 10.1039/D0SM02009E.
Related Concept Videos
01:21Polymer Classification: Crystallinity
3.5K
Unlike ionic or small covalent molecules, polymers do not form crystalline solids due to the diffusion limitations of their long-chain structures. However, polymers contain microscopic crystalline domains separated by amorphous domains.
Crystalline domains are the regions where polymer chains are aligned in an orderly manner and held together in proximity by intermolecular forces. For example, chains in the crystalline domains of polyethylene and nylon are bound together by van der Waals...
Crystalline domains are the regions where polymer chains are aligned in an orderly manner and held together in proximity by intermolecular forces. For example, chains in the crystalline domains of polyethylene and nylon are bound together by van der Waals...
3.5K
01:26Polymer Classification: Stereospecificity
2.9K
Polymerization generates chiral centers along the entire backbone of a polymer chain. Accordingly, the stereochemistry of the substituent group has a significant effect on polymer properties. Polymers formed from monosubstituted alkene monomers feature chiral carbons at every alternate position in the polymer backbone. Relative to the predominant orientation of substituents at the adjacent chiral carbons, the polymer can exist in three different configurations: isotactic, syndiotactic, and...
2.9K
01:10Polymers: Molecular Weight Distribution
4.1K
For any given polymer, the weight average molecular weight (Mw) is higher than, if not equal to, the number average molecular weight (Mn). The only situation in which the weight average molecular weight and the number average molecular weight are equal is when a polymer consists only of chains with equal molecular weight. However, this never happens in a synthetic polymer, since it is difficult to control the polymerization process up to a molecular level with accuracy to a hundred percent.
4.1K
01:08Molecular Weight of Step-Growth Polymers
2.6K
Step growth polymerization involves bi or multifunctional monomers. Bifunctional monomers react to form linear step growth polymers, whereas multifunctional monomers react to form non-linear or branched polymers.
As the step-growth polymerization involves step-wise condensation of monomers, the molecular weight also builds up eventually. Consequently, high molecular weight polymers are obtained at the late stages of the polymerization, where 99% of monomers have been consumed.
The extent of the...
As the step-growth polymerization involves step-wise condensation of monomers, the molecular weight also builds up eventually. Consequently, high molecular weight polymers are obtained at the late stages of the polymerization, where 99% of monomers have been consumed.
The extent of the...
2.6K
02:28Effect of Temperature Change on Reaction Rate
4.5K
The Arrhenius equation,
4.5K
00:57Cationic Chain-Growth Polymerization: Mechanism
2.5K
The cationic polymerization mechanism consists of three steps: initiation, propagation, and termination. In the initiation step of the polymerization process, the π bond of a monomer gets protonated by the Lewis acid catalyst, which is formed from boron trifluoride and water. The protonation of the π bond generates a carbocation stabilized by the electron‐donating group. In the propagation step, the π bond of the second monomer acts as a nucleophile and attacks the...
2.5K