Related Experiment Video

Updated: Nov 3, 2025

Writing Bragg Gratings in Multicore Fibers
08:48

Writing Bragg Gratings in Multicore Fibers

Published on: April 20, 2016

8.3K

Experimental characterization of group and phase delays induced by bending and twisting in multi-core fibers

Riccardo Veronese, Nicolas K Fontaine, Haoshuo Chen

    Optics Letters
    |June 1, 2021
    PubMed

    More Related Videos

    Micro/Nano-scale Strain Distribution Measurement from Sampling Moiré Fringes06:56

    Micro/Nano-scale Strain Distribution Measurement from Sampling Moiré Fringes

    Published on: May 23, 2017

    12.5K
    Fabrication and Characterization of Disordered Polymer Optical Fibers for Transverse Anderson Localization of Light09:19

    Fabrication and Characterization of Disordered Polymer Optical Fibers for Transverse Anderson Localization of Light

    Published on: July 29, 2013

    11.7K

    Related Concept Videos

    Bending and Torsional Moments01:20

    Bending and Torsional Moments

    Bending and torsional moments are two fundamental concepts in structural engineering. They play an important role in understanding the behavior of materials and structures under different loading conditions.
    The reaction developed in a structural element when subjected to an external force causes the element to bend. When a structural element bends upwards, it creates compressive normal forces on the top and tensile normal forces on the bottom, resulting in a couple that determines the bending...
    4.8K
    Bending of Curved Members - Strain Analysis01:14

    Bending of Curved Members - Strain Analysis

    The mechanics of deformation in curved members, such as beams or arches, under bending moments, involve complex responses. When such a member, symmetric about the y-axis and shaped like a segment of a circle centered at point C, is subjected to equal and opposite forces, its curvature and surface lengths change significantly. This alteration results in the shift of the curvature's center from C to C', indicating a tighter curve.
    The important part of bending analysis for such a member...
    308
    Unsymmetric Bending01:18

    Unsymmetric Bending

    Unsymmetrical bending occurs when the bending moment applied to a structural member does not align with its principal axis. This misalignment leads to complex stress distributions and deflection patterns that differ from those in symmetrical bending, and are essential for designing structures to withstand different loading conditions. In unsymmetrical bending, the neutral axis—where stress is zero—does not necessarily align with the geometric axes of the cross-section. The...
    577
    Residual Stresses in Bending01:18

    Residual Stresses in Bending

    In the study of elastoplastic members subjected to bending moments, understanding the loading and unloading phases is crucial for assessing material behavior and structural integrity. During the loading phase, as the bending moment increases, the material initially responds elastically, adhering to Hooke's Law, where stress is directly proportional to strain. When the load exceeds the yield strength, plastic deformation occurs, resulting in permanent strain and deformation that remains even...
    361
    Unsymmetric Bending - Angle of Neutral Axis01:15

    Unsymmetric Bending - Angle of Neutral Axis

    Unsymmetrical bending occurs when a structural member is subjected to bending moments in a plane that does not align with the member's principal axes. This scenario typically arises in beams and other structural components when loads are applied at non-ideal angles, introducing complexities in stress analysis.
    When a bending moment is applied at an angle θ concerning the vertical axis of a symmetrical member, it can be resolved into components along the member's principal...
    584
    Design of Prismatic Beams for Bending01:23

    Design of Prismatic Beams for Bending

    The design of prismatic beams, structural elements with a uniform cross-section, focuses on ensuring safety and structural integrity under load. The design process begins by determining the allowable stress, either from material properties tables, or by dividing the material's ultimate strength by a safety factor. This safety factor is essential for accommodating uncertainties, and varies depending on the material—timber, steel, or concrete—with each having unique strength and...
    459