Related Experiment Video

Updated: Nov 2, 2025

Calibration of Vector Network Analyzer for Measurements in Radio Frequency Propagation Channels
10:00

Calibration of Vector Network Analyzer for Measurements in Radio Frequency Propagation Channels

Published on: June 2, 2020

21.8K

Independent Calculation of Move Lists for Incumbent Protection in a Multi-SAS Shared Spectrum Environment

Michael R Souryal1, Thao T Nguyen1

  • 1National Institute of Standards and Technology, Communications Technology Laboratory, Gaithersburg, MD, 20899 USA.

IEEE Wireless Communications Letters
|June 14, 2021
PubMed

Keywords:
Aggregate interferenceCBRSincumbent protectionspectrum access systemspectrum sharing

More Related Videos

Large Scale Energy Efficient Sensor Network Routing Using a Quantum Processor Unit05:30

Large Scale Energy Efficient Sensor Network Routing Using a Quantum Processor Unit

Published on: September 8, 2023

879
Continuous-Wave Propagation Channel-Sounding Measurement System - Testing, Verification, and Measurements09:36

Continuous-Wave Propagation Channel-Sounding Measurement System - Testing, Verification, and Measurements

Published on: June 25, 2021

3.3K

Related Concept Videos

Radial System Protection01:23

Radial System Protection

Radial systems employ time-delay overcurrent relays to reduce load interruptions. When a fault occurs, the nearest breaker opens first, while upstream breakers remain closed due to longer delay settings. This approach ensures minimal disruption to the rest of the system.
In a radial system with a fault downstream of the third breaker, ideally, only the third breaker will open, isolating the fault and interrupting the load connected beyond it. The second breaker has a longer delay setting,...
190
Line Protection with Impedance Relays01:27

Line Protection with Impedance Relays

Coordinating time-delay overcurrent relays in complex radial systems and directional overcurrent relays in multi-source transmission loops can be challenging. Impedance relays address these issues by responding to the voltage-to-current ratio, specifically measuring the apparent impedance of a line. These relays become more sensitive during faults as current increases and voltage decreases, thereby reducing the apparent impedance.
Under normal conditions, low load currents keep the measured...
179
Distributed Loads: Problem Solving01:21

Distributed Loads: Problem Solving

Beams are structural elements commonly employed in engineering applications requiring different load-carrying capacities. The first step in analyzing a beam under a distributed load is to simplify the problem by dividing the load into smaller regions, which allows one to consider each region separately and calculate the magnitude of the equivalent resultant load acting on each portion of the beam. The magnitude of the equivalent resultant load for each region can be determined by calculating...
862
Calculation of Self-inductance01:29

Calculation of Self-inductance

The self-inductance of a circuit, often simply called the inductance, is a purely geometric factor that depends only on the circuit component's structure. More specifically, it depends on the shape and size of the component that lets the flux pass through it, thus inducing an electric field that opposes any current passing through it.
Since the effect of the induced electric field and the back EMF generated depends on the rate of change of current and the self-inductance, the inductance...
552
Multimachine Stability01:25

Multimachine Stability

Multimachine stability analysis is crucial for understanding the dynamics and stability of power systems with multiple synchronous machines. The objective is to solve the swing equations for a network of M machines connected to an N-bus power system.
In analyzing the system, the nodal equations represent the relationship between bus voltages, machine voltages, and machine currents. The nodal equation is given by:
264
Distributed Loads01:19

Distributed Loads

Distributed loads are a common type of load that engineers and scientists encounter in various practical situations. Distributed loads often refer to a type of load spread over a surface or a structure and can be modeled as continuous force per unit area.
For example, consider a bookshelf filled with books stacked vertically adjacent to each other. The weight of the books is evenly distributed over the length of the shelf. As a result, the pressure at different locations on the surface of the...
736