Related Experiment Video

Updated: Oct 31, 2025

Data Communication Based on MQTT in a Polymer Extrusion Process
08:15

Data Communication Based on MQTT in a Polymer Extrusion Process

Published on: July 15, 2022

3.6K

Relationship between manufacturing complexity, strategy, and performance of manufacturing industries in Indonesia

Hendri Dwi Saptioratri Budiono1, Rahmat Nurcahyo2, Muhammad Habiburrahman2

  • 1Department of Mechanical Engineering, Faculty of Engineering, Universitas Indonesia, Kampus Baru UI Depok, 16424 Indonesia.

Heliyon
|June 28, 2021
PubMed

Keywords:
Manufacturing complexityManufacturing performanceManufacturing strategyQuality strategy

More Related Videos

Operation of the Collaborative Composite Manufacturing CCM System10:09

Operation of the Collaborative Composite Manufacturing CCM System

Published on: October 1, 2019

6.8K
The Modular Design and Production of an Intelligent Robot Based on a Closed-Loop Control Strategy11:53

The Modular Design and Production of an Intelligent Robot Based on a Closed-Loop Control Strategy

Published on: October 14, 2017

11.9K

Related Concept Videos

Steel Manufacturing01:26

Steel Manufacturing

Steel manufacturing is a multi-stage process that begins by smelting iron ore into cast iron in a blast furnace. This initial stage involves layering iron ore with coke, a type of fuel, and crushed limestone within the furnace. The coke is ignited with a high volume of air, leading to the creation of carbon monoxide, which acts to reduce the iron ore to pure iron.
During this smelting process, limestone plays a crucial role by forming slag. Slag captures impurities within the molten iron, such...
945
Production Efficiency01:01

Production Efficiency

Net production efficiency (NPE) is the efficiency at which organisms assimilate energy into biomass for the next trophic level. Due to low metabolic rates and less energy spent on thermoregulatory processes, the NPE of ectotherms (cold-blooded animals) is 10 times higher than endotherms (warm-blooded animals).
17.3K
Factors Affecting Workability01:24

Factors Affecting Workability

The workability of concrete is a critical characteristic that influences the ease of mixing, handling, and finishing the concrete. It is affected by several factors including water content, aggregate properties, and admixtures like air entrainment. Water plays a fundamental role as it lubricates the concrete mix, facilitating easier movement and placement. However, the water requirement varies depending on the texture and shape of aggregates. Finer particles and angular, rough-textured...
164
Factors Affecting Activity Coefficient01:17

Factors Affecting Activity Coefficient

The extended Debye-Hückel equation indicates that the activity coefficient of an ion in an aqueous solution at 25°C depends on three partially interdependent properties: the ionic strength of the solution, the charge of the ion, and the ion size. 
The activity coefficient value for an ion is close to one when the solution has almost zero ionic strength, i.e., when the solution shows close to ideal behavior. As the ionic strength of the solution increases from 0 to 0.1 mol/L, a...
1.2K
Journal Bearings01:23

Journal Bearings

Journal bearings are mechanical components that support and provide lateral stability to rotating shafts and axles. They are crucial in reducing friction, wear, and vibration in machinery such as engines, turbines, and pumps. The principle behind journal bearings is forming a thin lubricant film between the bearing surface and the rotating shaft, which minimizes direct contact and reduces frictional forces.
To better understand the concept of journal bearings, consider a rope winch with dry or...
869
Angle of Twist: Problem Solving01:13

Angle of Twist: Problem Solving

An electric motor applies a torque of 700 N·m to an aluminum shaft, triggering a stable rotation. Two pulleys, B and C, are subjected to torques of 300 N·m and 400 N·m, respectively. The modulus of rigidity is provided as 25 GPa. With the knowledge of the length and diameter of each segment, the twist angle between the two pulleys can be computed. First, a section cut is made between pulleys B and C, and the cut cross-section is analyzed using a free-body diagram. Given that the...
498