Related Experiment Video

Updated: Oct 29, 2025

Biophysical Characterization of Flagellar Motor Functions
06:08

Biophysical Characterization of Flagellar Motor Functions

Published on: January 18, 2017

8.4K

Analysis of the Motional Stark Effect (MSE) diagnostic to measure the rotational transform and current profile in the

M Sanders1, K Ida2, M Yoshinuma2

  • 1Department of Applied Physics, Eindhoven University of Technology, Eindhoven 5600 MB, The Netherlands.

The Review of Scientific Instruments
|July 10, 2021
PubMed

More Related Videos

Magnetic Tweezers for the Measurement of Twist and Torque11:41

Magnetic Tweezers for the Measurement of Twist and Torque

Published on: May 19, 2014

23.5K
Optimized Setup and Protocol for Magnetic Domain Imaging with In Situ Hysteresis Measurement09:43

Optimized Setup and Protocol for Magnetic Domain Imaging with In Situ Hysteresis Measurement

Published on: November 7, 2017

9.6K

Related Concept Videos

Torque On A Current Loop In A Magnetic Field01:13

Torque On A Current Loop In A Magnetic Field

The most common application of magnetic force on current-carrying wires is in electric motors. These consist of loops of wire, which are placed between the magnets with a magnetic field. When current flows through the loops, the magnetic field applies torque, which causes the shaft to rotate, thus converting electrical energy to mechanical energy.
Consider a rectangular current-carrying loop containing N turns of wire, placed in a uniform magnetic field. The net force on a current-carrying loop...
5.0K
Angle of Twist: Problem Solving01:13

Angle of Twist: Problem Solving

An electric motor applies a torque of 700 N·m to an aluminum shaft, triggering a stable rotation. Two pulleys, B and C, are subjected to torques of 300 N·m and 400 N·m, respectively. The modulus of rigidity is provided as 25 GPa. With the knowledge of the length and diameter of each segment, the twist angle between the two pulleys can be computed. First, a section cut is made between pulleys B and C, and the cut cross-section is analyzed using a free-body diagram. Given that the...
485
Magnetic Field Of A Current Loop01:16

Magnetic Field Of A Current Loop

Consider a circular loop with a radius a, that carries a current I. The magnetic field due to the current at an arbitrary point P along the axis of the loop can be calculated using the Biot-Savart law.
5.5K
Thin-Walled Hollow Shafts01:15

Thin-Walled Hollow Shafts

In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution...
322
Force On A Current Loop In A Magnetic Field01:17

Force On A Current Loop In A Magnetic Field

Magnetic forces on wires carrying current are most frequently applied in motors. A DC motor is a device that converts electrical energy into mechanical work. In motors, wire loops are enclosed in a magnetic field. When current flows through the loops, the magnetic field applies torque, which causes the shaft to rotate. The direction of the current is reversed once the loop's surface area is lined up with the magnetic field, causing a constant torque on the loop. During the process,...
3.6K
Deformation in a Circular Shaft01:10

Deformation in a Circular Shaft

One of the distinctive characteristics of circular shafts is their ability to maintain their cross-sectional integrity under torsion. In other words, each cross-section continues to exist as a flat, unaltered entity, simply rotating like a solid, rigid slab. To understand the distribution of shearing stress within such a shaft, consider a cylindrical section inside this circular shaft. This section has a length of L and a radius of R, with one end fixed. The radius of the cylindrical section is...
541