Related Experiment Video

Updated: Oct 28, 2025

Real-Time DC-dynamic Biasing Method for Switching Time Improvement in Severely Underdamped Fringing-field Electrostatic MEMS Actuators
11:44

Real-Time DC-dynamic Biasing Method for Switching Time Improvement in Severely Underdamped Fringing-field Electrostatic MEMS Actuators

Published on: August 15, 2014

10.5K

Input-to-State Stability of Nonlinear Impulsive Systems Subjects to Actuator Saturation and External Disturbance

Haitao Zhu, Xiaodi Li, Shiji Song

    IEEE Transactions on Cybernetics
    |July 14, 2021
    PubMed

    More Related Videos

    An Experimental Platform to Study the Closed-loop Performance of Brain-machine Interfaces10:51

    An Experimental Platform to Study the Closed-loop Performance of Brain-machine Interfaces

    Published on: March 10, 2011

    14.0K
    A Human-machine-interface Integrating Low-cost Sensors with a Neuromuscular Electrical Stimulation System for Post-stroke Balance Rehabilitation11:06

    A Human-machine-interface Integrating Low-cost Sensors with a Neuromuscular Electrical Stimulation System for Post-stroke Balance Rehabilitation

    Published on: April 12, 2016

    10.6K

    Related Concept Videos

    Transient and Steady-state Response01:24

    Transient and Steady-state Response

    In control systems, test signals are essential for evaluating performance under various conditions. The ramp function is effective for systems undergoing gradual changes, while the step function is suitable for assessing systems facing sudden disturbances. For systems subjected to shock inputs, the impulse function is the most appropriate test signal.
    These test signals are integral in designing control systems to exhibit two key performance aspects: transient response and steady-state...
    336
    Stability01:28

    Stability

    The time response of a linear time-invariant (LTI) system can be divided into transient and steady-state responses. The transient response represents the system's initial reaction to a change in input and diminishes to zero over time. In contrast, the steady-state response is the behavior that persists after the transient effects have faded.
    The stability of an LTI system is determined by the roots of its characteristic equation, known as poles. A system is stable if it produces a bounded...
    218
    Second Order systems II01:18

    Second Order systems II

    In an underdamped second-order system, where the damping ratio ζ is between 0 and 1, a unit-step input results in a transfer function that, when transformed using the inverse Laplace method, reveals the output response. The output exhibits a damped sinusoidal oscillation, and the difference between the input and output is termed the error signal. This error signal also demonstrates damped oscillatory behavior. Eventually, as the system reaches a steady state, the error diminishes to zero.
    233
    Linear Approximation in Time Domain01:21

    Linear Approximation in Time Domain

    Nonlinear systems often require sophisticated approaches for accurate modeling and analysis, with state-space representation being particularly effective. This method is especially useful for systems where variables and parameters vary with time or operating conditions, such as in a simple pendulum or a translational mechanical system with nonlinear springs.
    For a simple pendulum with a mass evenly distributed along its length and the center of mass located at half the pendulum's length,...
    171
    BIBO stability of continuous and discrete -time systems01:24

    BIBO stability of continuous and discrete -time systems

    System stability is a fundamental concept in signal processing, often assessed using convolution. For a system to be considered bounded-input bounded-output (BIBO) stable, any bounded input signal must produce a bounded output signal. A bounded input signal is one where the modulus does not exceed a certain constant at any point in time.
    To determine the BIBO stability, the convolution integral is utilized when a bounded continuous-time input is applied to a Linear Time-Invariant (LTI) system....
    618
    Feedback control systems01:26

    Feedback control systems

    Feedback control systems are categorized in various ways based on their design, analysis, and signal types.
    Linear feedback systems are theoretical models that simplify analysis and design. These systems operate under the principle that their output is directly proportional to their input within certain ranges. For instance, an amplifier in a control system behaves linearly as long as the input signal remains within a specific range. However, most physical systems exhibit inherent nonlinearity...
    530