Related Experiment Video

Updated: Oct 25, 2025

Author Spotlight: Enhancing Fiber Composite Laminate Quality with the Wet Hand Lay-Up/Vacuum Bag Process
09:54

Author Spotlight: Enhancing Fiber Composite Laminate Quality with the Wet Hand Lay-Up/Vacuum Bag Process

Published on: June 30, 2023

2.6K

Effect of Manufacturing on the Transverse Response of Polymer Matrix Composites

Sagar P Shah1, Marianna Maiarù1

  • 1Department of Mechanical Engineering, University of Massachusetts Lowell, Lowell, MA 01854, USA.

Polymers
|August 10, 2021
PubMed

Keywords:
curingdamage mechanicsfinite elementsprocess modelingthermoset composites

More Related Videos

Magnet Assisted Composite Manufacturing: A Flexible New Technique for Achieving High Consolidation Pressure in Vacuum Bag/Lay-Up Processes09:41

Magnet Assisted Composite Manufacturing: A Flexible New Technique for Achieving High Consolidation Pressure in Vacuum Bag/Lay-Up Processes

Published on: May 17, 2018

13.7K
Manufacturing Of Robust Natural Fiber Preforms Utilizing Bacterial Cellulose as Binder10:47

Manufacturing Of Robust Natural Fiber Preforms Utilizing Bacterial Cellulose as Binder

Published on: May 22, 2014

27.7K

Related Concept Videos

Deformations in a Transverse Cross Section01:21

Deformations in a Transverse Cross Section

When a material is subjected to uniaxial stress, it elongates or contracts in the direction of the applied force, and also undergoes changes in the perpendicular directions. This behavior is crucial for understanding how materials behave under stress and is governed by mechanical properties such as Poisson's ratio v, which measures the ratio of transverse strain to axial strain.
As the material stretches, it expands or contracts in orthogonal directions to the load. This phenomenon varies...
380
Bending of Members Made of Several Materials01:08

Bending of Members Made of Several Materials

In analyzing a structural member composed of two different materials with identical cross-sectional areas, it is crucial to understand how their distinct elastic properties affect the member's response under load. The analysis involves assessing stress and strain distributions using the transformed section concept, which accounts for variations in material properties.
Hooke's Law determines stress in each material, stating that stress is proportional to strain but varies due to each...
339
Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
219
Plastic Behavior01:21

Plastic Behavior

A material's elastic behavior is characterized by the disappearance of stress once the load is removed, allowing the material to return to its original state. However, when stress surpasses the yield point, yielding commences, marking the onset of plastic deformation or permanent set. This change from elastic to plastic behavior is influenced by the peak stress value and the duration before the load is removed. An intriguing observation occurs when a specimen is loaded, unloaded, and...
327
Cell-matrix's Response to Mechanical Forces01:13

Cell-matrix's Response to Mechanical Forces

In animal cells, the extracellular matrix allows cells within tissues to withstand external stresses and transmits signals from the outside of the cell to the inside. The extracellular matrix is extensive, and its composition varies between different types of tissues. For example, the reticular fibers and ground substance make up the ECM in loose connective tissue, while collagen and bone minerals make up the ECM of bone tissue. 
Anchoring junctions mechanically attach a cell to the...
3.0K
Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.
373