Related Experiment Video

Updated: Oct 25, 2025

Shaping the Amplitude and Phase of Laser Beams by Using a Phase-only Spatial Light Modulator
08:39

Shaping the Amplitude and Phase of Laser Beams by Using a Phase-only Spatial Light Modulator

Published on: January 28, 2019

10.0K

Performance Degradation in Cross-Eye Jamming Due to Amplitude/Phase Instability between Jammer Antennas

Je-An Kim1, Joon-Ho Lee1

  • 1Department of Information and Communication Engineering, Sejong University, Seoul 05006, Korea.

Sensors (Basel, Switzerland)
|August 10, 2021
PubMed

Keywords:
Taylor expansionamplitude ratiocross-eyejammingphase difference

More Related Videos

Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping09:43

Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping

Published on: March 20, 2017

10.1K
Efficiently Recording the Eye-Hand Coordination to Incoordination Spectrum07:30

Efficiently Recording the Eye-Hand Coordination to Incoordination Spectrum

Published on: March 21, 2019

8.1K

Related Concept Videos

Time and frequency -Domain Interpretation of Phase-lag Control01:21

Time and frequency -Domain Interpretation of Phase-lag Control

Phase-lag controllers are widely used in control systems to improve stability and reduce steady-state errors. A dimmer switch controlling the brightness of a light bulb serves as a practical example of phase-lag control, gradually adjusting the bulb's brightness. Mathematically, phase-lag control or low-pass filtering is represented when the factor 'a' is less than 1.
Phase-lag controllers do not place a pole at zero, but instead influence the steady-state error by amplifying any...
165
Aliasing01:18

Aliasing

Accurate signal sampling and reconstruction are crucial in various signal-processing applications. A time-domain signal's spectrum can be revealed using its Fourier transform. When this signal is sampled at a specific frequency, it results in multiple scaled replicas of the original spectrum in the frequency domain. The spacing of these replicas is determined by the sampling frequency.
If the sampling frequency is below the Nyquist rate, these replicas overlap, preventing the original...
304
Propagation Speed of Electromagnetic Waves01:30

Propagation Speed of Electromagnetic Waves

Electromagnetic waves are consistent with Ampere's law. Assuming there is no conduction current Ampere's law is given as:
4.1K
Interference: Path Lengths01:10

Interference: Path Lengths

Consider two sources of sound, that may or may not be in phase, emitting waves at a single frequency, and consider the frequencies to be the same.
Two special sources may be considered when they are in phase. This can be easily achieved by feeding the two sources from the same source. An example would be synchronizing the two speakers by feeding them with the same source, such as the sound waves produced by a tuning fork. This setup ensures that the two sources have the same frequency and are...
1.5K
IR Spectrum Peak Splitting: Symmetric vs Asymmetric Vibrations01:08

IR Spectrum Peak Splitting: Symmetric vs Asymmetric Vibrations

Identical bonds within a polyatomic group can stretch symmetrically (in-phase) or asymmetrically (out-of-phase). Similar to hydrogen bonding, these vibrations also influence the shape of the IR peak. Generally, asymmetric stretching frequencies are higher than symmetric stretching frequencies. For example, primary amines exhibit two distinct IR peaks between 3300–3500 cm−1 corresponding to the symmetric and asymmetric N-H stretching, while secondary amines exhibit a single...
1.3K
Time and frequency -Domain Interpretation of Phase-lead Control01:24

Time and frequency -Domain Interpretation of Phase-lead Control

Phase-lead controllers are commonly used in various control systems to enhance response speed and stability. Adjusting the brightness on a television screen offers a practical example of phase-lead control. When contrast is enhanced, a phase-lead controller is employed. Mathematically, phase-lead control is identified when the first parameter is smaller than the second.
The design of phase-lead control involves the strategic placement of poles and zeros to balance steady-state error and system...
173