Related Experiment Video

Updated: Oct 17, 2025

Spatial Multiobjective Optimization of Agricultural Conservation Practices using a SWAT Model and an Evolutionary Algorithm
11:53

Spatial Multiobjective Optimization of Agricultural Conservation Practices using a SWAT Model and an Evolutionary Algorithm

Published on: December 9, 2012

13.1K

Modeling and optimizing an agro-supply chain considering different quality grades and storage systems for fresh

Fatemeh Keshavarz-Ghorbani1, Seyed Hamid Reza Pasandideh1

  • 1Department of Industrial Engineering, Faculty of Engineering, Kharazmi University, Tehran, Iran.

Journal of Combinatorial Optimization
|October 11, 2021
PubMed

Keywords:
Agro-supply chainBenders decomposition algorithmInventory managementQuality score

More Related Videos

Design and Optimization Strategies of a High-Performance Vented Box14:23

Design and Optimization Strategies of a High-Performance Vented Box

Published on: June 9, 2023

1.3K
Author Spotlight: Optimization of Processing Technology for Tiebangchui with Zanba Based on CRITIC Combined with Box-Behnken Response Surface Method09:16

Author Spotlight: Optimization of Processing Technology for Tiebangchui with Zanba Based on CRITIC Combined with Box-Behnken Response Surface Method

Published on: May 12, 2023

1.3K

Related Concept Videos

Bending of Material: Problem Solving01:09

Bending of Material: Problem Solving

In this lesson, determine the ratio of the maximum bending moments applied to two metal pipes, given that both pipes can withstand a maximum stress of 100 MPa. Both pipes have an outer radius of 1.8 cm. Pipe A has an inner radius of 1.5 cm, and Pipe B has an inner radius of 1 cm. The ratio of the maximum bending moment applied to two metallic pipes, each with a different inner and outer radius, is determined by considering their dimensions. The inner radius of the first pipe is 1.5 cm, and for...
298
Distributed Loads: Problem Solving01:21

Distributed Loads: Problem Solving

Beams are structural elements commonly employed in engineering applications requiring different load-carrying capacities. The first step in analyzing a beam under a distributed load is to simplify the problem by dividing the load into smaller regions, which allows one to consider each region separately and calculate the magnitude of the equivalent resultant load acting on each portion of the beam. The magnitude of the equivalent resultant load for each region can be determined by calculating...
821
Bending of Curved Members - Strain Analysis01:14

Bending of Curved Members - Strain Analysis

The mechanics of deformation in curved members, such as beams or arches, under bending moments, involve complex responses. When such a member, symmetric about the y-axis and shaped like a segment of a circle centered at point C, is subjected to equal and opposite forces, its curvature and surface lengths change significantly. This alteration results in the shift of the curvature's center from C to C', indicating a tighter curve.
The important part of bending analysis for such a member...
289
Design Example: Design of an Irrigation Channel01:27

Design Example: Design of an Irrigation Channel

Trapezoidal channels are widely used in irrigation systems due to their cost-effectiveness and efficiency in conveying water. Trapezoidal channels feature a flat bottom and sloping sides, making them stable and easier to construct compared to other shapes. The bottom width and side slope ratio are determined based on the required flow capacity and site conditions. The side slope is kept gentle for unlined channels to prevent soil erosion.Hydraulic parameters in channel design include the flow...
301
Design Example: Aggregate Gradation01:24

Design Example: Aggregate Gradation

The right type and quality of aggregates are crucial for concrete as they significantly influence its properties, mix proportions, and cost-effectiveness. If different sources are available for sand, the commonly used fine aggregate in concrete, the selection of sand is primarily based on its gradation.
The grading, or particle-size distribution, of sand is determined using sieve analysis, with standard sizes ranging from 150 μm to 10 mm (ASTM No. 100 sieve to 3⁄8 in. sieve). Sand is...
159
Shear and Bending Moment Diagram: Problem Solving01:24

Shear and Bending Moment Diagram: Problem Solving

When analyzing a beam supporting concentrated loads and a distributed load, drawing the shear and bending moment diagrams is essential. These diagrams help understand the internal forces and moments acting on the beam, which is crucial for designing safe and efficient structures. Follow these steps to create the shear and bending moment diagrams:
Draw a Free-Body Diagram: Start by drawing a free-body diagram of the entire beam, including the concentrated loads, distributed load, and reaction...
2.1K