Related Experiment Video

Updated: Oct 17, 2025

Operation of the Collaborative Composite Manufacturing CCM System
10:09

Operation of the Collaborative Composite Manufacturing CCM System

Published on: October 1, 2019

6.8K

Design of a Multi-Point Kinematic Coupling for a High Precision Telescopic Simultaneous Measurement System

Raquel Acero1,2, Juan José Aguilar1,2, Francisco Javier Brosed1,2

  • 1Department of Design and Manufacturing Engineering, University of Zaragoza, María de Luna 3, 50018 Zaragoza, Spain.

Sensors (Basel, Switzerland)
|October 13, 2021
PubMed

Keywords:
interferometrykinematic couplingmachine toolmultilaterationtelescopic system

More Related Videos

Design and Implementation of a Bespoke Robotic Manipulator for Extra-corporeal Ultrasound07:41

Design and Implementation of a Bespoke Robotic Manipulator for Extra-corporeal Ultrasound

Published on: January 7, 2019

9.3K
Magnetic Tweezers for the Measurement of Twist and Torque11:41

Magnetic Tweezers for the Measurement of Twist and Torque

Published on: May 19, 2014

23.5K

Related Concept Videos

Design Example: Measuring Distance Between Two Points with Obstructions01:10

Design Example: Measuring Distance Between Two Points with Obstructions

When measuring distances in areas with physical obstructions, such as a lake in a field, surveyors must employ techniques to calculate accurate lengths without direct line measurements. One effective method is the offset technique, which allows for precise distance estimation over inaccessible stretches.In this scenario, a surveyor must measure a side of an area that crosses a lake. Since the measuring tape cannot span the lake, the surveyor begins by establishing a baseline that aligns with...
163
Moment of a Couple: Problem Solving01:30

Moment of a Couple: Problem Solving

The moment of couple is an essential concept in physics and engineering, used to calculate the rotational force, or torque, that is created when a couple —two equal and opposite forces—acts on an object.
The moment of a couple is found by multiplying the magnitude of one of the forces by the perpendicular distance between the line of action of the two forces. This creates a twisting force, which can be used to rotate an object. The moment of a couple is used to solve problems...
1.3K
One-Degree-of-Freedom System01:24

One-Degree-of-Freedom System

In mechanical engineering, one-degree-of-freedom systems form the basis of a wide range of electrical and mechanical components. Using these models, engineers can predict the behavior of various parts in a larger system, which gives them insight into how different forces interact with each other.
A one-degree-of-freedom system is defined by an independent variable that determines its state and behavior. One example of a one-degree-of-freedom system is a simple harmonic oscillator, such as a...
574
Adjusting a Traverse01:12

Adjusting a Traverse

In the site survey of a four-sided traverse, internal angles are essential to ensure geometric accuracy. The survey revealed that the sum of the measured internal angles was 359 degrees and 48 minutes, which is 12 minutes less than the expected 360 degrees. This discrepancy signals an error likely arising from measurement inaccuracies during the fieldwork.To rectify this error, the adjustment process involved distributing the 12-minute shortfall equally across the four internal angles. By...
166
Relative Motion Analysis using Rotating Axes-Problem Solving01:29

Relative Motion Analysis using Rotating Axes-Problem Solving

Consider a crane whose telescopic boom rotates with an angular velocity of 0.04 rad/s and angular acceleration of 0.02 rad/s2. Along with the rotation, the boom also extends linearly with a uniform speed of 5 m/s. The extension of the boom is measured at point D, which is measured with respect to the fixed point C on the other end of the boom. For the given instant, the distance between points C and D is 60 meters.
Here, in order to determine the magnitude of velocity and acceleration for point...
480
Design of Transmission Shafts01:16

Design of Transmission Shafts

The design of a transmission shaft is governed by two primary specifications: the power it transmits and its rotational speed. These parameters guide the selection of the shaft's material and cross-sectional dimensions, ensuring that the material's maximum shearing stress remains within the elastic limit while transmitting the desired power at the given speed. The system's power is intrinsically linked to the applied torque. The torque applied to the shaft can be calculated by...
518