Related Experiment Video
Updated: Oct 16, 2025

09:32
Manufacturing Abdominal Aorta Hydrogel Tissue-Mimicking Phantoms for Ultrasound Elastography Validation
Published on: September 19, 2018
15.5K
Commentary: May the force(s) be with you: Loading conditions and the aorta
Gerhard A Holzapfel1, Abe DeAnda2, Keshava Rajagopal3
1Institute of Biomechanics, Graz University of Technology, Graz, Austria; Department of Structural Engineering, Norwegian University of Science and Technology, Trondheim, Norway.
The Journal of Thoracic and Cardiovascular Surgery
|October 18, 2021
Summary
No abstract available in PubMed .
Related Concept Videos
The Aorta
1.5K
The aorta is the largest artery in the human body. It originates from the left ventricle of the heart and extends down to the abdomen, where it splits into two smaller arteries. Structurally, it can be divided into four main parts: the ascending aorta, the aortic arch, the thoracic aorta, and the abdominal aorta.
The average diameter of the aorta is approximately 2-3 cm, but the size can vary depending on the section of the aorta and the individual's age, sex, and body size. The aorta is...
The average diameter of the aorta is approximately 2-3 cm, but the size can vary depending on the section of the aorta and the individual's age, sex, and body size. The aorta is...
1.5K
Aneurysm I: Introduction
41
An aortic aneurysm is a localized outpouching or dilation at a weak point in the artery wall. It may involve different parts of the aorta, such as the abdominal aorta, aortic arch, or thoracic aorta.Etiological factorsSeveral disorders are associated with aortic aneurysms.Congenital causes, such as primary connective tissue disorders like Marfan syndrome, impact the integrity and strength of connective tissues, notably affecting the aorta. Marfan syndrome is a genetic disorder that specifically...
41
Stress: General Loading Conditions
401
To grasp the intricacy of real-world conditions where multiple loads are applied simultaneously to a structure, one might visualize a section passing through a specific point within a body, aligned parallel to the xy plane. This section is subjected to various forces, including original loads, normal forces, and shearing forces.
The shearing force, possessing potential directionality within the plane of the section, is simplified into two component forces running parallel to the x and y axes....
The shearing force, possessing potential directionality within the plane of the section, is simplified into two component forces running parallel to the x and y axes....
401
Aneurysm II: Clinical Manifestations and Diagnostic Studies
48
Thoracic, aortic arch and abdominal aneurysms are significant vascular conditions that can present with various clinical manifestations and lead to serious complications. Understanding these manifestations and the appropriate diagnostic studies is essential for effective management and treatment.Thoracic Aortic AneurysmsThoracic aortic aneurysms often remain asymptomatic until they reach a size that impinges on adjacent structures. They typically cause deep, diffuse chest pain that radiates to...
48
Thoracic Aorta
866
The thoracic section of the aorta begins at the T5 vertebra and extends to the T12 level at the diaphragm, initially progressing through the mediastinum to the left of the spinal column. Throughout its course in the thoracic segment, the thoracic aorta emits various offshoots known collectively as visceral and parietal branches. The branches that predominantly supply blood to visceral organs are termed visceral branches and include bronchial, pericardial, esophageal, and mediastinal arteries,...
866
Stresses under Combined Loadings
256
When analyzing a bent tube with a circular cross-section subjected to multiple forces, it is crucial to determine the stress distribution in order to maintain structural integrity under varied load conditions.
The process begins by slicing the tube at critical points and analyzing the internal forces and stress components at these sections, focusing on the centroid. Normal stresses, generated by axial forces and bending moments, are either compressive or tensile and vary across the section from...
The process begins by slicing the tube at critical points and analyzing the internal forces and stress components at these sections, focusing on the centroid. Normal stresses, generated by axial forces and bending moments, are either compressive or tensile and vary across the section from...
256

