Related Experiment Video

Updated: Oct 15, 2025

Residue-Free Fabrication of van der Waals Heterostructures of Two-Dimensional Materials
04:57

Residue-Free Fabrication of van der Waals Heterostructures of Two-Dimensional Materials

Published on: July 18, 2025

522

Atomistic Mechanics of Torn Back Folded Edges of Triangular Voids in Monolayer WS2

Gyeong Hee Ryu1, Gang Seob Jung2, Hyoju Park3

  • 1School of Materials Science and Engineering, Gyeongsang National University, Jinju, 52828, Republic of Korea.

Small (Weinheim an Der Bergstrasse, Germany)
|October 28, 2021
PubMed

Keywords:
STEMWS 2foldingreactive molecular dynamicstearing edge

More Related Videos

Fabrication of Three-Dimensional Graphene-Based Polyhedrons via Origami-Like Self-Folding14:52

Fabrication of Three-Dimensional Graphene-Based Polyhedrons via Origami-Like Self-Folding

Published on: September 23, 2018

9.1K
Fabricating van der Waals Heterostructures with Precise Rotational Alignment09:25

Fabricating van der Waals Heterostructures with Precise Rotational Alignment

Published on: July 5, 2019

9.7K

Related Concept Videos

Transformation of Plane Stress01:18

Transformation of Plane Stress

Studying stress transformation is essential in understanding how stress components within a material, like a cube under plane stress, change with rotation. This change is analyzed by considering a prismatic element within the cube. As the element rotates, the stress components acting on it—both normal and shearing stresses—change in magnitude and orientation. This change is quantified using trigonometric functions of the rotation angle, relating the forces acting on the rotated element's...
422
Concept of Pressure at a Point01:15

Concept of Pressure at a Point

The concept of pressure at a point in a fluid establishes that pressure within a fluid is uniform in all directions at a specific location. This uniformity occurs because fluid molecules exert force evenly across any point due to their random motion and continuous collisions within the fluid. Pressure at a point is determined by the surrounding fluid molecules and is influenced by factors like depth and density, rather than by shape or orientation.
In a fluid at rest, pressure acts equally in...
444
Thin-Walled Hollow Shafts01:15

Thin-Walled Hollow Shafts

In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution...
286
Unsymmetric Loading of Thin-Walled Members01:23

Unsymmetric Loading of Thin-Walled Members

Thin-walled members with non-symmetrical cross-sections are vital to engineering structures, offering material efficiency and structural integrity. However, unsymmetrical loading on these members leads to complex stress distributions, resulting in simultaneous bending and twisting can cause deformation or structural failure. The interaction between bending and twisting requires detailed analysis to ensure structural resilience.
The concept of the shear center is crucial in countering the...
189
Plastic Deformations of Members with a Single Plane of Symmetry01:21

Plastic Deformations of Members with a Single Plane of Symmetry

When a structural member undergoes plastic deformation due to bending, it is crucial to understand the position of the neutral axis and the stress distribution. This member, characterized by a single plane of symmetry, exhibits a uniform stress distribution, with negative stress above the neutral axis and positive stress below. Notably, the neutral axis does not align with the centroid of the cross-section. This misalignment is typical in cases where the cross-section is not rectangular or...
167
Unsymmetric Loading of Thin-Walled Members: Problem Solving01:07

Unsymmetric Loading of Thin-Walled Members: Problem Solving

The shear center of a channel section with uniform thickness, height, and width, is determined by computing the shear force in the member and calculating the moments of inertia of the sections.
To compute the shear forces, find the shear flow at a specific distance from the endpoint using the vertical shear and the moment of inertia values. The total shear force on the flange is calculated by integrating the shear flow from one end of the flange to the other.
Next, calculate the moments of...
222