Related Experiment Video

Updated: Oct 14, 2025

Improving the Combustion Performance of a Hybrid Rocket Engine using a Novel Fuel Grain with a Nested Helical Structure
07:58

Improving the Combustion Performance of a Hybrid Rocket Engine using a Novel Fuel Grain with a Nested Helical Structure

Published on: January 18, 2021

6.1K

Combination of Pilot Injection and a NH3-SCR System To Reduce NOx Emissions of a Nonroad Compression Ignition Engine

Tansu Shang1,2,3, Chenyang Fan4, Zheng Fu5

  • 1State Key Laboratory of Engines, Tianjin University, Tianjin 300072, PR China.

ACS Omega
|November 8, 2021
PubMed

More Related Videos

Automated, High-resolution Mobile Collection System for the Nitrogen Isotopic Analysis of NOx07:14

Automated, High-resolution Mobile Collection System for the Nitrogen Isotopic Analysis of NOx

Published on: December 20, 2016

11.8K
Calibrated Passive Sampling - Multi-plot Field Measurements of NH3 Emissions with a Combination of Dynamic Tube Method and Passive Samplers10:29

Calibrated Passive Sampling - Multi-plot Field Measurements of NH3 Emissions with a Combination of Dynamic Tube Method and Passive Samplers

Published on: March 21, 2016

12.5K

Related Concept Videos

Internal Combustion Engine01:20

Internal Combustion Engine

The internal combustion engine is a heat engine that uses the byproducts of combustion as the working fluid instead of using a heat transfer medium to transfer heat. The combustion is done in a way that produces high-pressure combustion products that can be expanded through a turbine or piston to create work. Internal combustion engines can again be categorized into three kinds: (1) spark ignition gasoline engines, most commonly used in automobiles, (2) compression ignition diesel engines that...
1.9K
Otto and Diesel Cycle01:27

Otto and Diesel Cycle

An Otto engine is a four-stroke engine that uses a mixture of gasoline and air as the working fuel. The fuel is injected into the cylinder, and the piston is moved completely down so that the cylinder is at maximum volume. By moving the piston up, adiabatic compression takes place. The spark plug ignites the gasoline-air mixture, and the burning fuel adds heat to the system at a constant volume. The heated mixture expands adiabatically and gets further cooled by exhausting heat, and this cyclic...
2.3K
Gas Chromatography: Sample Injection Systems01:08

Gas Chromatography: Sample Injection Systems

In gas chromatography, the sample is introduced as a vapor plug into the carrier gas stream for high efficiency and resolution. A microsyringe injects the sample solution into a heated sample port, vaporizing it and mixing it with the carrier gas. This process is important to ensure the sample is properly prepared for analysis. Thermally sensitive samples can be injected directly into the column and volatilized by slowly increasing the column temperature.
Two primary injection methods are used...
738
Preparation of Amines: Reductive Amination of Aldehydes and Ketones01:38

Preparation of Amines: Reductive Amination of Aldehydes and Ketones

Carbonyl compounds and primary amines undergo reductive amination first to produce imines, followed by secondary amines in the same reaction mixture, using selective reducing agents like sodium cyanoborohydride or sodium triacetoxyborohydride. Reductive amination produces different degrees of substitution of amines depending on the starting amine substrate.
3.2K
Work Done in an Adiabatic Process01:20

Work Done in an Adiabatic Process

Consider the adiabatic compression of an ideal gas in the cylinder of an automobile diesel engine. The gasoline vapor is injected into the cylinder of an automobile engine when the piston is in its expanded position. The temperature, pressure, and volume of the resulting gas-air mixture are 20 °C, 1.00 x 105 N/m2, and 240 cm3 , respectively. The mixture is then compressed adiabatically to a volume of 40 cm3. Note that, in the actual operation of an automobile engine, the compression is not...
3.6K
Preparation of Amines: Reduction of Oximes and Nitro Compounds01:29

Preparation of Amines: Reduction of Oximes and Nitro Compounds

Oximes can be reduced to primary amines using catalytic hydrogenation, hydride reduction, or sodium metal reduction. The reduction of aliphatic and aromatic nitro compounds to primary amines takes place by either catalytic hydrogenation or by using active metals like Fe, Zn, and Sn in the presence of an acid.
Though catalytic hydrogenation can reduce nitrobenzenes, the reduction is nonselective in the presence of other functional groups. For instance, if nitrobenzene contains an aldehyde group,...
4.2K