Related Experiment Video

Updated: Oct 13, 2025

Fabrication and Characterization of Thickness Mode Piezoelectric Devices for Atomization and Acoustofluidics
10:39

Fabrication and Characterization of Thickness Mode Piezoelectric Devices for Atomization and Acoustofluidics

Published on: August 5, 2020

7.1K

Analysis of Air-Coupled Transducer-Based Elastic Waves Generation in CFRP Plates

Tomasz Wandowski1, Damian Mindykowski1, Pawel Kudela1

  • 1Institute of Fluid-Flow Machinery, Polish Academy of Sciences, Fiszera 14 St., 80-231 Gdansk, Poland.

Sensors (Basel, Switzerland)
|November 13, 2021
PubMed

Keywords:
air-coupled transducercomposite fiber-reinforced polymerscanning laser doppler vibrometry

More Related Videos

Characterization of Full Set Material Constants and Their Temperature Dependence for Piezoelectric Materials Using Resonant Ultrasound Spectroscopy07:44

Characterization of Full Set Material Constants and Their Temperature Dependence for Piezoelectric Materials Using Resonant Ultrasound Spectroscopy

Published on: April 27, 2016

9.7K
Micro/Nano-scale Strain Distribution Measurement from Sampling Moiré Fringes06:56

Micro/Nano-scale Strain Distribution Measurement from Sampling Moiré Fringes

Published on: May 23, 2017

12.4K

Related Concept Videos

Fluid Pressure over Flat Plate of Constant Width01:05

Fluid Pressure over Flat Plate of Constant Width

When a body is submerged in water, it experiences fluid pressure acting normal on its surface and distributed over its area. For better design structures, it is crucial to determine the magnitude and location of the resultant force acting on the surface. In the case of a rectangular plate of constant width submerged in water, the pressure increases with depth, resulting in a linearly varying trapezoidal pressure distribution from the upper to the lower edge of the plate.
The resultant force...
2.2K
Fluid Pressure over Flat Plate of Variable Width01:02

Fluid Pressure over Flat Plate of Variable Width

When a flat plate is submerged in a fluid, the fluid exerts pressure on the plate. This pressure can lead to many different phenomena, including drag and buoyancy. To understand the behavior of the fluid over a flat plate of variable width, it is essential to analyze the distribution of the pressure exerted.
The pressure distribution on the plate can be calculated by determining the force that acts on a differential area strip of the plate. Thus, the magnitude of the force is equal to the...
1.8K
Fluid Pressure over Curved Plate of Constant Width01:12

Fluid Pressure over Curved Plate of Constant Width

When a curved plate of constant width is submerged in a liquid, the pressure acting normal to the plate varies continuously both in magnitude and direction. Calculating the magnitude and location of the resultant force at a point is often challenging for such cases. One of the methods to determine the resultant force and its location involves separately calculating the horizontal and vertical components of the resultant force. This complex calculation can be simplified by representing the...
1.7K
Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
193
Elastic Curve from the Load Distribution01:16

Elastic Curve from the Load Distribution

The structural behavior of beams under distributed loads is critical for engineering analysis, which focuses on predicting how beams bend and react under such conditions. Different types of beams (e.g., cantilever, supported, or overhanging) behave differently under distributed load conditions.
For all beams, the analysis of the beam's reaction to distributed loads begins by understanding the relationship between a beam's load and the resulting shear forces and bending moments.
278
Standing Waves in a Cavity01:28

Standing Waves in a Cavity

A household microwave and lasers are examples of standing electromagnetic waves in a cavity. When two conducting metal plates are placed parallel at the nodal planes, it creates a cavity where standing waves are formed. The cavity between the two planes is analogous to a stretched string held at the points x = 0 and x = L. Here, the distance 'L' between the two planes must be an integer multiple of half of the wavelength. The wavelengths that satisfy this condition are given by:
1.1K