Related Experiment Video

Updated: Oct 12, 2025

Scalable Quantum Integrated Circuits on Superconducting Two-Dimensional Electron Gas Platform
05:39

Scalable Quantum Integrated Circuits on Superconducting Two-Dimensional Electron Gas Platform

Published on: August 2, 2019

9.8K

Mathematical models for thermionic emission current density of graphene emitter

Olukunle C Olawole1, Dilip K De2, Sunday O Oyedepo3

  • 1Department of Physics, Covenant University, Ota, Ogun State, Nigeria. olukunle.olawole@covenantuniversity.edu.ng.

Scientific Reports
|November 19, 2021
PubMed

More Related Videos

Fabrication of Gate-tunable Graphene Devices for Scanning Tunneling Microscopy Studies with Coulomb Impurities11:42

Fabrication of Gate-tunable Graphene Devices for Scanning Tunneling Microscopy Studies with Coulomb Impurities

Published on: July 24, 2015

15.6K
High-resolution Thermal Micro-imaging Using Europium Chelate Luminescent Coatings09:01

High-resolution Thermal Micro-imaging Using Europium Chelate Luminescent Coatings

Published on: April 16, 2017

7.9K

Related Concept Videos

Carrier Transport01:21

Carrier Transport

The generation of electrical current in semiconductors is fundamentally driven by two mechanisms: drift and diffusion. These processes are essential for the functionality and performance of semiconductor-based devices.
Drift Current:
The drift of charge carriers is started by an external electric field (E). Charged particles, such as electrons and holes, experience an acceleration between collisions with lattice atoms. For electrons, this results in a drift velocity (vd) given by:
631
Modeling of Diode Forward Characteristics01:19

Modeling of Diode Forward Characteristics

Understanding the behavior of diodes when forward-biased is a fundamental aspect of electronic circuit design and analysis. This analysis primarily utilizes two models: the exponential diode model and the constant-voltage-drop model. The exponential model comes into play when the source voltage exceeds 0.5 volts, pushing the diode current to rise exponentially above the saturation current. This relationship is graphically depicted in the current-voltage (I-V) curve, illustrating the diode's...
749
Characteristics of BJT01:17

Characteristics of BJT

The Bipolar Junction Transistor (BJT), specifically in a common-emitter configuration, exhibits distinct current-voltage characteristics crucial for understanding its behavior in electronic circuits. These characteristics are established through experimental measurements of voltage and current relationships.
For input characteristics, the base-emitter voltage is varied, maintaining a constant collector-emitter voltage. This setup reveals a Shockley-type dependence of the collector current on...
900
Current Density01:21

Current Density

The total amount of current flowing through one unit value of a cross-sectional area is referred to as current density. If the current flow is uniform, the amount of current flowing through a conductor is the same at all points along the conductor, even if the conductor area varies. The current density consists of the local magnitude and direction of the charge flow, which varies from point to point. Current density is measured in amperes per meter square, and direction is defined as the net...
4.4K
Working Principle of BJT01:15

Working Principle of BJT

A Bipolar Junction Transistor (BJT), specifically a PNP transistor in a common-base configuration, effectively amplifies or switches electronic signals by controlling the flow of charge carriers. This discussion focuses on its operation in the active mode.
In the PNP configuration, the emitter is heavily doped with positive charge carriers (holes), while the base is lightly doped with negative carriers (electrons). This setup allows for a forward bias across the emitter-base junction,...
778
Small-Signal Analysis of BJT Amplifiers01:21

Small-Signal Analysis of BJT Amplifiers

Small signal analysis is a fundamental approach used in electronics to understand how a Bipolar Junction Transistor (BJT) amplifier processes signals. In the active region, the BJT is designed for linear amplification. The transistor's behavior under these conditions is governed by its instantaneous base-emitter voltage VBE, a sum of the DC bias VBE, and a small AC signal VBE, resulting in the collector current iC. Here, the collector current has a DC component and an AC component.
1.4K