Related Experiment Video

Updated: Oct 3, 2025

Twin-Screw Extrusion Process to Produce Renewable Fiberboards
07:21

Twin-Screw Extrusion Process to Produce Renewable Fiberboards

Published on: January 27, 2021

6.6K

Characteristic Properties of a Bamboo-Based Board Combined with Bamboo Veneers and Vacuum Heat-Treated Round Bamboo

Yu-Hsuan Yang1, Min-Jay Chung2, Tung-Lin Wu3

  • 1Department of Forestry, National Chung Hsing University, Taichung 402, Taiwan.

Polymers
|February 15, 2022
PubMed

Keywords:
dimension stabilityflexural propertiesrotary-cut bamboo veneerround bamboo stickvacuum heat treatment

More Related Videos

Fabrication and Design of Wood-Based High-Performance Composites08:08

Fabrication and Design of Wood-Based High-Performance Composites

Published on: November 9, 2019

13.5K
Manufacturing Of Robust Natural Fiber Preforms Utilizing Bacterial Cellulose as Binder10:47

Manufacturing Of Robust Natural Fiber Preforms Utilizing Bacterial Cellulose as Binder

Published on: May 22, 2014

27.7K

Related Concept Videos

Wood Products01:21

Wood Products

Wood products encompass a broad range of materials crafted from wood strands, veneers, lumber, and even waste wood-like shreds, designed for both structural and nonstructural purposes. Various specialized wood products have been developed to enhance strength, durability, and versatility in building applications.
Glue-laminated wood, often referred to as glulam, combines multiple smaller pieces of dimensional lumber using adhesives to form a single, larger piece. Cross-laminated timber consists...
144
Wood Panel Products01:18

Wood Panel Products

Wood panel products are essential materials used in construction for applications such as flooring, siding, and roofing, typically available in standard dimensions of 4 feet by 8 feet, with thicknesses varying from one-quarter of an inch to one and one-eighth inches. Among the most common types of wood panels is plywood, which is produced by gluing multiple layers of thin wood veneers under pressure. The grain of the outer veneers runs lengthwise, while the grains of the interior layers run...
138
Veneer01:19

Veneer

Veneer refers to a thin sheet of wood, typically produced to a thickness of about one-eighth of an inch or less. This material is crafted through various methods, the most common being rotary cutting. In this process, a log is mounted into a large lathe and spun against a knife edge, peeling off a continuous strip of wood as the knife penetrates deeper into the rotating log, creating a rotary-cut veneer.
Other veneering techniques include plain-slicing, quarter-slicing, and rift-slicing. These...
143
Introduction to Wood01:19

Introduction to Wood

Wood, derived from trees, is a versatile and widely used construction material. Trees feature a trunk surrounded by a protective layer of dead bark. Beneath this outer layer lies the living bark, followed by the cambium, and then the sapwood which transitions into heartwood as it matures. At the center of the trunk is the pith. The age of a tree can be discerned by examining its growth rings, which are concentric bands visible in the trunk's cross-section.
The structural integrity of the...
353
Wood Surfacing01:14

Wood Surfacing

Wood surfacing is a critical finishing process designed to smoothen the wood surface, enhance its dimensional accuracy, and make handling safer. This process compensates for potential shrinkage during the seasoning phase by marginally increasing the wood dimensions before surfacing. It also helps correct some distortions that may occur as the wood dries.
The equipment used in the surfacing process is a plane equipped with rotating blades. This tool efficiently smoothens the wood surface and can...
161
Softwoods and Hardwoods01:28

Softwoods and Hardwoods

Softwoods and hardwoods, derived from different types of trees, are distinguished by their leaf structures and cellular compositions, each serving unique purposes in construction and manufacturing. Softwoods come from cone-bearing trees with needle-like leaves and are predominantly composed of longitudinal cells called tracheids and a smaller proportion of radial cells known as rays. Due to their cellular structure, softwoods are commonly used in construction for structural frames, sheathing,...
267