Related Experiment Video

Updated: Sep 30, 2025

Measurement of the Rheology of Crude Oil in Equilibrium with CO2 at Reservoir Conditions
10:38

Measurement of the Rheology of Crude Oil in Equilibrium with CO2 at Reservoir Conditions

Published on: June 6, 2017

12.9K

Experimental analyzing the effect of n-heptane concentration and angular frequency on the viscoelastic behavior of

Mohammadjavad Fazeli1, Mehdi Escrochi2, Zohreh Sadat Hosseini3

  • 1Department of Chemical Engineering, Shiraz Branch, Islamic Azad University, Shiraz, Iran.

Scientific Reports
|March 11, 2022
PubMed

More Related Videos

In Situ Visualization of the Phase Behavior of Oil Samples Under Refinery Process Conditions11:20

In Situ Visualization of the Phase Behavior of Oil Samples Under Refinery Process Conditions

Published on: February 21, 2017

6.8K
On-line Analysis of Nitrogen Containing Compounds in Complex Hydrocarbon Matrixes07:49

On-line Analysis of Nitrogen Containing Compounds in Complex Hydrocarbon Matrixes

Published on: August 5, 2016

10.8K

Related Concept Videos

Physical Properties of Alkanes02:33

Physical Properties of Alkanes

Alkanes are nonpolar molecules due to the presence of only carbon and hydrogen atoms. The electronegativity difference between carbon and hydrogen is minimal, and hence alkanes have a zero dipole moment. This leads to the presence of only dispersion forces between the molecules. The strength of dispersion forces is dependent on the surface area of the molecules on which they act. Since the surface area increases with the molecular length for straight-chain alkanes, the dispersion forces also...
12.6K
¹H NMR of Conformationally Flexible Molecules: Variable-Temperature NMR01:15

¹H NMR of Conformationally Flexible Molecules: Variable-Temperature NMR

The axial and equatorial protons in cyclohexane can be distinguished by performing a variable-temperature NMR experiment. In this process, except for one proton, the remaining eleven protons are replaced by deuterium. The deuterium substitution avoids the possible peak splitting caused by the spin-spin coupling between the adjacent protons. The remaining proton flips between the axial and equatorial positions.
1.2K
Mass Spectrometry: Branched Alkane Fragmentation01:29

Mass Spectrometry: Branched Alkane Fragmentation

This lesson delves into the mass spectrometry of branched alkane fragmentation. Branched alkanes possess secondary or tertiary carbon atoms, which generate relatively stable carbocations if the cleavage occurs at the branching point. The high stability of carbocations drives the instant fragmentation of branched alkanes. Accordingly, the branched alkane's molecular ion peak is very weak or invisible in the mass spectra, especially in comparison to a linear alkane.
1.2K
Mass Spectrometry: Long-Chain Alkane Fragmentation01:18

Mass Spectrometry: Long-Chain Alkane Fragmentation

The molecular ions of linear alkanes prefer to fragment at the carbon-carbon bond away from the end of the chain since the cleavage of an inner bond creates a stable carbocation and a stable radical. Consequently, the mass signals of linear alkanes feature intense peaks in the middle of the mass-to-charge ratio plot with weaker peaks on either end. The fragmentation of each carbon-carbon bond with the release of a methyl group in each splitting leads to prominent peaks in the mass spectra...
1.8K
Conformations of Cycloalkanes02:29

Conformations of Cycloalkanes

Adolf von Baeyer attempted to explain the instabilities of small and large cycloalkane rings using the concept of angle strain — the strain caused by the deviation of bond angles from the ideal 109.5° tetrahedral value for sp3  hybridized carbons. However, while cyclopropane and cyclobutane are strained, as expected from their highly compressed bond angles, cyclopentane is more strained than predicted, and cyclohexane is virtually strain-free. Hence, Baeyer’s theory that...
12.8K
Stress Concentrations in Circular Shafts01:18

Stress Concentrations in Circular Shafts

Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
280