Related Experiment Video

Updated: Sep 30, 2025

20 mJ, 1 ps Yb:YAG Thin-disk Regenerative Amplifier
10:17

20 mJ, 1 ps Yb:YAG Thin-disk Regenerative Amplifier

Published on: July 12, 2017

11.7K

Millijoule 265 fs Tm:YAP regenerative amplifier for driving ultrabroad band collinear mid-infrared optical parametric

Seyed Ali Rezvani, Takao Fuji

    Optics Express
    |March 18, 2022
    PubMed

    More Related Videos

    Infrared Degenerate Four-wave Mixing with Upconversion Detection for Quantitative Gas Sensing10:42

    Infrared Degenerate Four-wave Mixing with Upconversion Detection for Quantitative Gas Sensing

    Published on: March 22, 2019

    6.3K
    Quantum State Engineering of Light with Continuous-wave Optical Parametric Oscillators09:23

    Quantum State Engineering of Light with Continuous-wave Optical Parametric Oscillators

    Published on: May 30, 2014

    14.7K

    Related Concept Videos

    MOSFET Amplifiers01:17

    MOSFET Amplifiers

    The MOSFET, when operating in its active region, functions as a voltage-controlled current source. In this region, the gate-to-source voltage controls the drain current. This principle underlies the operation of the transconductance MOSFET amplifier. The output current is directed through a load resistor to convert this amplifier into a voltage amplifier. The output voltage is then obtained by subtracting the voltage drop across the load resistance from the supply voltage. This process results...
    229
    BJT Amplifiers01:14

    BJT Amplifiers

    Bipolar Junction Transistors (BJTs) are pivotal components in amplifier circuits, functioning as voltage-controlled current sources in their active region. This characteristic allows them to efficiently control the collector current through variations in the base-emitter voltage. Essentially, BJTs amplify power due to their ability to take a weak input signal and output a much stronger signal.
    In BJT amplifier configurations, particularly in common-emitter setups, the transistor's role...
    625
    Small-Signal Analysis of MOSFET Amplifiers01:23

    Small-Signal Analysis of MOSFET Amplifiers

    In small-signal analysis, a MOSFET transistor amplifier acts as a linear amplifier when operating in its saturation region. The gate-to-source voltage (VGS) of the MOSFET is the sum of the DC biasing voltage and the small time-varying input signal. This combination sets up the operating point and modulates the drain current (ID) that flows from the drain to the source. When a small AC signal is superimposed on the DC bias voltage at the gate, the instantaneous drain current comprises three...
    764
    Cascaded Op Amps01:16

    Cascaded Op Amps

    Operational amplifiers (op-amps) are versatile electronic components that can be interconnected in a cascade - one after another in a linear sequence. This cascading is possible due to their infinite input resistance and zero output resistance, allowing them to maintain their input-output relationships even when connected in series.
    In a cascaded system, each op-amp is referred to as a stage. The output of one stage drives the input of the subsequent stage. As the input signal passes through...
    769
    Small-Signal Analysis of BJT Amplifiers01:21

    Small-Signal Analysis of BJT Amplifiers

    Small signal analysis is a fundamental approach used in electronics to understand how a Bipolar Junction Transistor (BJT) amplifier processes signals. In the active region, the BJT is designed for linear amplification. The transistor's behavior under these conditions is governed by its instantaneous base-emitter voltage VBE, a sum of the DC bias VBE, and a small AC signal VBE, resulting in the collector current iC. Here, the collector current has a DC component and an AC component.
    1.3K
    Maximum Power Transfer01:16

    Maximum Power Transfer

    Numerous practical applications within engineering disciplines, such as telecommunications, necessitate optimizing power delivery to a connected load. This pursuit, however, entails inherent internal losses, which can either equal or exceed the power supplied to the load. The Thevenin equivalent circuit is helpful in finding the maximum power a linear circuit can deliver to a load. It is assumed in this context that the load resistance can be adjusted.
    By substituting the entire circuit with...
    466