Related Experiment Video

Updated: Sep 29, 2025

Parametric Optimization Design Method for Friction Plates of Hydro-Viscous Clutches
10:58

Parametric Optimization Design Method for Friction Plates of Hydro-Viscous Clutches

Published on: July 22, 2025

137

A Complex Vibration Analysis of a Drive System Equipped with an Innovative Prototype of a Flexible Torsion Clutch as

Andrzej N Wieczorek1, Łukasz Konieczny2, Rafał Burdzik2

  • 1Department of Mining Mechanization and Robotisation, Faculty of Mining, Safety Engineering and Industrial Automation, Silesian University of Technology, 44-100 Gliwice, Poland.

Sensors (Basel, Switzerland)
|March 26, 2022
PubMed

Keywords:
Campbell diagramSTFTflexible torsion clutchorder analysisvibrations

More Related Videos

Tactile Vibrating Toolkit and Driving Simulation Platform for Driving-Related Research07:15

Tactile Vibrating Toolkit and Driving Simulation Platform for Driving-Related Research

Published on: December 18, 2020

4.6K
Design and Application of a Fault Detection Method Based on Adaptive Filters and Rotational Speed Estimation for an Electro-Hydrostatic Actuator06:45

Design and Application of a Fault Detection Method Based on Adaptive Filters and Rotational Speed Estimation for an Electro-Hydrostatic Actuator

Published on: October 28, 2022

1.8K

Related Concept Videos

Design of Transmission Shafts - Stress Analysis01:15

Design of Transmission Shafts - Stress Analysis

Designing a transmission shaft requires a thorough understanding of the stresses induced by bending moments and torques, especially in systems where power is transferred through gears. These forces create force-couple systems at the centers of the shaft's cross-sections, leading to both transverse and torsional loading. Although shearing stresses from transverse loads are typically smaller than those from torques and are often overlooked, the significant normal stresses from these loads...
510
Design of Transmission Shafts01:16

Design of Transmission Shafts

The design of a transmission shaft is governed by two primary specifications: the power it transmits and its rotational speed. These parameters guide the selection of the shaft's material and cross-sectional dimensions, ensuring that the material's maximum shearing stress remains within the elastic limit while transmitting the desired power at the given speed. The system's power is intrinsically linked to the applied torque. The torque applied to the shaft can be calculated by...
496
Transmission Shafts: Problem Solving01:09

Transmission Shafts: Problem Solving

Designing a solid shaft that transmits power from a motor to a machine tool involves a series of calculations to ensure the shaft can withstand the stresses applied by bending moments and torques. First, calculate the torque exerted on the gear, considering the power transmitted by the shaft and its rotational speed. Following this, compute the tangential forces acting on the gears, which directly relate to the torque and the gear radius.
Next, use bending moment diagrams for the shaft to...
305
Stresses in a Shaft01:18

Stresses in a Shaft

The shaft PQ is subjected to a twisting force when equal and opposite torques are applied on either side. A section that cuts perpendicular to the shaft's axis at any arbitrary point R is examined to understand this. When the free-body diagram of the QR segment is analyzed, it reveals the shearing forces exerted by the PR portion onto the QR segment as the shaft experiences twisting.
Applying equilibrium conditions to the QR segment establishes that the internal shearing forces within the...
544
Stress Concentrations in Circular Shafts01:18

Stress Concentrations in Circular Shafts

Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
276
Circular Shaft - Stresses in Linear Range01:13

Circular Shaft - Stresses in Linear Range

Consider a scenario where a circular shaft is subject to torque that remains within the boundaries of Hooke's Law, avoiding any permanent deformation. So, the formula for shearing strain is revisited. This formula is multiplied by the modulus of rigidity, and then Hooke's Law for the shearing stress and strain is applied. As a result, the equation for shearing stress in a shaft can be derived.
396