Related Experiment Video

Updated: Sep 26, 2025

Protocol for Relative Hydrodynamic Assessment of Tri-leaflet Polymer Valves
11:12

Protocol for Relative Hydrodynamic Assessment of Tri-leaflet Polymer Valves

Published on: October 17, 2013

13.9K

Design Consideration Investigation of Soft-Valve Pipe

Xu Yang1, Yiniu Luo1, Chen Ji1

  • 1Institute of Marine Science and Technology, Shandong University, Qingdao 266237, China.

Micromachines
|April 23, 2022
PubMed

Keywords:
configurationsparameterssilicone pipesoft valve

More Related Videos

Author Spotlight: Advancing Cardiac Procedure Testing Prior to Embarking on Large Animal Studies06:56

Author Spotlight: Advancing Cardiac Procedure Testing Prior to Embarking on Large Animal Studies

Published on: August 25, 2023

1.1K
Mechanical Expansion of Steel Tubing as a Solution to Leaky Wellbores09:32

Mechanical Expansion of Steel Tubing as a Solution to Leaky Wellbores

Published on: November 20, 2014

12.4K

Related Concept Videos

Single Pipe Systems01:24

Single Pipe Systems

In pipe flow analysis, problems are typically categorized into three types — Type I, Type II, and Type III — based on the known parameters and the desired outcome. Each type of problem addresses specific engineering requirements using fluid properties, pipe characteristics, and operational conditions.
In a Type I problem, fluid properties (density and viscosity), pipe characteristics (including diameter, length, and surface roughness), and the flow rate or average velocity are...
198
General Characteristics of Pipe Flow I01:22

General Characteristics of Pipe Flow I

Pipe flow refers to the movement of fluids within fully enclosed conduits, typically cylindrical in shape, such as water pipes or hydraulic hoses. These conduits are designed to withstand high-pressure gradients that drive fluid movement, contrasting with open-channel flows, where gravity is the primary driving force. Rectangular conduits, like air conditioning and heating ducts, generally operate at lower pressures and are less suited for high-pressure applications.
The classification of fluid...
1.3K
General Characteristics of Pipe Flow II01:24

General Characteristics of Pipe Flow II

When fluid enters a pipe, it first passes through the entrance region, where the velocity profile adjusts due to viscous effects. In this region, a boundary layer forms along the pipe walls and grows until it fully occupies the pipe's cross-section. Once the boundary layer merges, the flow becomes fully developed, with a steady velocity profile that remains consistent along the pipe's length.
The distance to reach a fully developed flow is called the entrance length and depends on the...
1.2K
Pipe Flowrate Measurement: Problem Solving01:28

Pipe Flowrate Measurement: Problem Solving

A spray tank system is engineered to uniformly distribute a pest-control liquid across plants by using a pressurized mechanism. The tank, pressurized to 150 kPa, holds the pesticide at a height of 0.80 meters. Liquid flows from the tank through a 1.9 meter pipe with a diameter of 0.015 meters, angled at 0.698 radians, ultimately reaching a 0.007 meter nozzle that sprays the pesticide. Accurate calculation of the system's flow rate is crucial to ensure uniform application, and this is...
606
Multiple Pipe Systems01:21

Multiple Pipe Systems

Multipipe systems consist of complex configurations of interconnected pipes designed to transport fluids efficiently across intricate networks. They are essential in engineering applications requiring precise control over flow distribution, pressure, and head loss. They are categorized into series, parallel, loop, and network configurations, each distinguished by unique flow characteristics and applications.
Series Configuration
In a series configuration, fluid flows sequentially from one pipe...
852
Bending of Material: Problem Solving01:09

Bending of Material: Problem Solving

In this lesson, determine the ratio of the maximum bending moments applied to two metal pipes, given that both pipes can withstand a maximum stress of 100 MPa. Both pipes have an outer radius of 1.8 cm. Pipe A has an inner radius of 1.5 cm, and Pipe B has an inner radius of 1 cm. The ratio of the maximum bending moment applied to two metallic pipes, each with a different inner and outer radius, is determined by considering their dimensions. The inner radius of the first pipe is 1.5 cm, and for...
266