Related Experiment Video

Updated: Sep 24, 2025

Flapping Soft Fin Deformation Modeling using Planar Laser-Induced Fluorescence Imaging
06:20

Flapping Soft Fin Deformation Modeling using Planar Laser-Induced Fluorescence Imaging

Published on: April 28, 2022

2.2K

Correction: Exploring the antifouling effect of elastic deformation by DEM-CFD coupling simulation

Limei Tian1, E Jin1, Jianfu Wang1

  • 1Key Laboratory of Bionic Engineering (Ministry of Education), Jilin University No. 5988 Renmin Street Changchun 130022 China lmtian@jlu.edu.cn.

RSC Advances
|May 9, 2022
PubMed
Summary

This study corrects a previously published article DOI. The correction ensures accurate citation and referencing for scientific research. This is vital for maintaining the integrity of scientific literature.

More Related Videos

Optical Coherence Tomography Based Biomechanical Fluid-Structure Interaction Analysis of Coronary Atherosclerosis Progression13:07

Optical Coherence Tomography Based Biomechanical Fluid-Structure Interaction Analysis of Coronary Atherosclerosis Progression

Published on: January 15, 2022

4.1K
Finite Element Modeling for the Simulation of the Quasi-Static Compression of Corrugated Tapered Tubes06:34

Finite Element Modeling for the Simulation of the Quasi-Static Compression of Corrugated Tapered Tubes

Published on: January 6, 2023

1.7K

Related Concept Videos

Deformation of Member under Multiple Loadings01:11

Deformation of Member under Multiple Loadings

When a rod is made of different materials or has various cross-sections, it must be divided into parts that meet the necessary conditions for determining the deformation. These parts are each characterized by their internal force, cross-sectional area, length, and modulus of elasticity. These parameters are then used to compute the deformation of the entire rod.
In the case of a member with a variable cross-section, the strain is not constant but depends on the position. The deformation of an...
228
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
202
Deformations in a Symmetric Member in Bending01:18

Deformations in a Symmetric Member in Bending

When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
281
Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.
339
Residual Stresses in Bending01:18

Residual Stresses in Bending

In the study of elastoplastic members subjected to bending moments, understanding the loading and unloading phases is crucial for assessing material behavior and structural integrity. During the loading phase, as the bending moment increases, the material initially responds elastically, adhering to Hooke's Law, where stress is directly proportional to strain. When the load exceeds the yield strength, plastic deformation occurs, resulting in permanent strain and deformation that remains even...
280
Equation of the Elastic Curve01:23

Equation of the Elastic Curve

The concept of curvature in plane curves, crucial in structural engineering, defines how sharply a beam bends under load. This curvature is determined using the curve's first and second derivatives.
Consider a cantilever beam with a point load at its free end (for instance, a diving board). When analyzing beam deflection with small slopes, the shape of the beam's elastic curve becomes key. The governing equation for this analysis involves the bending moment and the beam's flexural...
702