Related Experiment Video

Updated: Sep 20, 2025

Kinematic History of a Salient-recess Junction Explored through a Combined Approach of Field Data and Analog Sandbox Modeling
06:55

Kinematic History of a Salient-recess Junction Explored through a Combined Approach of Field Data and Analog Sandbox Modeling

Published on: August 5, 2016

8.3K

Dataset for centrifuge modelling of laterally monotonic loaded monopiles in saturated dense sand

Zhong-Sen Li1, Matthieu Blanc2, Luc Thorel2

  • 1Department of Civil Engineering, Aalto University, Otaniemi, Finland.

Data in Brief
|June 6, 2022
PubMed

Keywords:
Fibre Bragg gratingsOffshore wind turbine foundationSoil-pile interactionTension-compression asymmetry

More Related Videos

Visually Based Characterization of the Incipient Particle Motion in Regular Substrates: From Laminar to Turbulent Conditions11:51

Visually Based Characterization of the Incipient Particle Motion in Regular Substrates: From Laminar to Turbulent Conditions

Published on: February 22, 2018

8.8K
Visualization of Failure and the Associated Grain-Scale Mechanical Behavior of Granular Soils under Shear using Synchrotron X-Ray Micro-Tomography09:00

Visualization of Failure and the Associated Grain-Scale Mechanical Behavior of Granular Soils under Shear using Synchrotron X-Ray Micro-Tomography

Published on: September 29, 2019

13.5K

Related Concept Videos

Design Example: Aggregate Gradation01:24

Design Example: Aggregate Gradation

The right type and quality of aggregates are crucial for concrete as they significantly influence its properties, mix proportions, and cost-effectiveness. If different sources are available for sand, the commonly used fine aggregate in concrete, the selection of sand is primarily based on its gradation.
The grading, or particle-size distribution, of sand is determined using sieve analysis, with standard sizes ranging from 150 μm to 10 mm (ASTM No. 100 sieve to 3⁄8 in. sieve). Sand is...
152
Distributed Loads01:19

Distributed Loads

Distributed loads are a common type of load that engineers and scientists encounter in various practical situations. Distributed loads often refer to a type of load spread over a surface or a structure and can be modeled as continuous force per unit area.
For example, consider a bookshelf filled with books stacked vertically adjacent to each other. The weight of the books is evenly distributed over the length of the shelf. As a result, the pressure at different locations on the surface of the...
634
Relation Between the Distributed Load and Shear01:23

Relation Between the Distributed Load and Shear

Understanding the relationship between the distributed load and shear force in structural analysis is crucial for analyzing beams subjected to various loading conditions. Consider the case of a beam experiencing a distributed load, two concentrated loads, and a couple moment.
793
Centrifugation01:05

Centrifugation

Centrifugation is a separation technique based on differences in density or size. It is commonly used to separate solids from aqueous interferents. During centrifugation, the sample is placed in centrifugation tubes and spun at high angular velocity, which allows centrifugal force to act differentially on the different densities or masses of the components. After spinning, the supernatant liquid is decanted. Depending on the specific application, either the pellet or the supernatant is retained...
2.6K
Eccentric Loading01:16

Eccentric Loading

Eccentric loading is a crucial concept in the study of structural engineering and mechanics, particularly when analyzing the stability and stress distribution in columns. Unlike centric loading, where the force is applied along the centroidal axis, causing uniform compression, eccentric loading occurs when a force is applied off-center. This off-center application introduces not only direct compressive stress but also bending stress, significantly influencing the column's behavior under...
509
Bulk Density of Aggregate01:22

Bulk Density of Aggregate

Bulk density refers to the mass of aggregate particles that would fill a unit volume. The concept of bulk density originates from the inability to pack aggregate particles in a manner that completely eliminates void spaces. Hence, the term bulk refers to the volume that encompasses both the aggregates and the voids. This measurement is crucial when aggregates are batched by volume and is used to convert quantities by mass to volume.
Most natural mineral aggregates, like sand and gravel,...
695