Related Experiment Video

Updated: Sep 8, 2025

Modifying the Bank Erosion Hazard Index BEHI Protocol for Rapid Assessment of Streambank Erosion in Northeastern Ohio
13:00

Modifying the Bank Erosion Hazard Index BEHI Protocol for Rapid Assessment of Streambank Erosion in Northeastern Ohio

Published on: February 13, 2015

9.2K

Revised Iranian Water Quality Index (RIWQI): a tool for the assessment and management of water quality in Iran

Pejman Fathi1, Eisa Ebrahimi Dorche2, Mojgan Zare Shahraki1

  • 1Department of Natural Resources, Isfahan University of Technology, Isfahan, 84156-83111, Iran.

Environmental Monitoring and Assessment
|June 15, 2022
PubMed

Keywords:
Freshwater ecosystem monitoringKarun River BasinPCARating curves

More Related Videos

Preparation and Testing of Impedance-based Fluidic Biochips with RTgill-W1 Cells for Rapid Evaluation of Drinking Water Samples for Toxicity11:19

Preparation and Testing of Impedance-based Fluidic Biochips with RTgill-W1 Cells for Rapid Evaluation of Drinking Water Samples for Toxicity

Published on: March 7, 2016

9.2K
Screening for Endocrine Activity in Water Using Commercially-available In Vitro Transactivation Bioassays08:00

Screening for Endocrine Activity in Water Using Commercially-available In Vitro Transactivation Bioassays

Published on: December 4, 2016

7.6K

Related Concept Videos

Quality of Water01:19

Quality of Water

In concrete preparation, the quality of water is paramount as it affects the strength and durability of the concrete. Potable water is usually preferred; however, it must not have excessive sodium or potassium to prevent compromising the concrete's integrity. Water quality is typically evaluated based on impurities such as dissolved solids, chlorides, and sulfates, and its pH value is ideally between 6 and 8. Even slightly acidic natural water may be acceptable unless it contains harmful...
182
Testing Water Quality01:14

Testing Water Quality

When the quality of water for concrete preparation is uncertain, its impact on the setting time of cement and compressive strength of mortar is assessed by comparison with de-ionized or distilled water benchmarks. American Society for Testing and Materials (ASTM) C1602 requires the setting times to be within 90 minutes of the control, British Standard (BS) 3146:1980 allows a 30-minute variance in the initial setting, while British Standards European Norm (BS EN) 1008 specifies initial setting...
177
Weir01:24

Weir

A weir is a hydraulic structure designed to partially obstruct an open channel, enabling precise control and measurement of water flow. By forcing water to flow over or through it, a weir allows for accurate determination of discharge rates, making it an essential tool in water resource management. These structures are extensively used in regulating river flows, irrigation systems, and flood control channels.Types of Weirs and Their FeaturesWeirs are categorized primarily into sharp-crested and...
123
Weir: Problem Solving01:26

Weir: Problem Solving

Water flow in open channels is often measured using hydraulic structures such as weirs, which allow precise calculation of discharge. In a rectangular channel, flow rates are measured using three types of weirs: rectangular sharp-crested, triangular sharp-crested, and broad-crested. The weir head is set at a fixed height above the channel bottom, simplifying calculations and enabling the relationship between depth and flow rate to be analyzed.For the rectangular sharp-crested weir, the flow...
102
Therapeutic Index01:13

Therapeutic Index

The therapeutic index of a drug is a key parameter in pharmacology that quantifies the relative safety of a drug by calculating the ratio between the dose that causes toxicity in half the population (50%) to the dose that proves to be effective for half the population (50%). It provides a spectrum of doses for a particular drug ranging from effective to potentially toxic. To illustrate, consider an anticoagulant agent like warfarin. It possesses a narrow window within its therapeutic index to...
5.0K
Design Example: Design of an Irrigation Channel01:27

Design Example: Design of an Irrigation Channel

Trapezoidal channels are widely used in irrigation systems due to their cost-effectiveness and efficiency in conveying water. Trapezoidal channels feature a flat bottom and sloping sides, making them stable and easier to construct compared to other shapes. The bottom width and side slope ratio are determined based on the required flow capacity and site conditions. The side slope is kept gentle for unlined channels to prevent soil erosion.Hydraulic parameters in channel design include the flow...
212