Tuning the Selectivity of the Hydrogenation/Hydrogenolysis of 5-Hydroxymethylfurfural under Batch Multiphase and
Daily Rodríguez-Padrón1, Alvise Perosa1, Lilia Longo1
1Dipartimento di Scienze Molecolari e Nanosistemi, UniversitàCa' Foscari di Venezia, 30123, Venezia, Italy.
Abstract:
The hydrogenation/hydrogenolysis of 5-hydroxymethylfurfural (HMF) has been carried out either under single (aqueous) phase or batch multiphase (MP) conditions using mutually immiscible aqueous/hydrocarbon phases, 5 % Ru/C as a catalyst, and both with and without the use of trioctylmethyl phosphonium bis-(trifluoro methane) sulfonimide ([P8881 ][NTf2 ]) as an ionic liquid (IL). Alternatively, the hydrogenation of HMF was explored in the continuous-flow (CF) mode with the same catalyst. By changing reaction parameters, experiments were optimized towards the formation of three products: 2,5-bis(hydroxy methyl)furan (BHMF), 2,5-bis(hydroxymethyl)tetrahydrofuran (BHMTHF), and 1-hydroxyhexane-2,5-dione (HHD), which were obtained in up to 92, 90, and 99 % selectivity, respectively, at quantitative conversion. In particular, the single (aqueous) phase reaction of HMF (0.2 m) carried out for 18 h at 60 °C under 30 bar of H2 , allowed the exclusive synthesis of BHMF from the partial (carbonyl) hydrogenation of HMF, while the MP reaction run at a higher T and p (100 °C and 50 bar) proved excellent to achieve only HHD derived from a sequence of hydrogenation/hydrogenolysis. It is worth noting that under MP conditions, the catalyst was perfectly segregated in the IL, where it could be recycled without any leaching in the aqueous/hydrocarbon phases. Finally, the hydrogenation of HMF was explored in a H-Cube® flow reactor in the presence of different solvents, such as ethyl acetate, tetrahydrofuran, and ethanol. At 100 °C, 50 bar H2 , and a flow rate of 0.1 mL min-1 , the process was optimized towards the formation of the full hydrogenation product BHMTHF. Ethyl acetate proved the best solvent.
More Related Videos
Related Concept Videos
02:13Reduction of Alkenes: Catalytic Hydrogenation
Metals like palladium, platinum, and nickel are commonly used in their solid forms — fine powder on an inert surface. As these catalysts remain insoluble in the reaction mixture, they are referred to as heterogeneous catalysts.
The hydrogenation process takes place on the...
02:17Reduction of Alkenes: Asymmetric Catalytic Hydrogenation
The metal catalyst used can be either heterogeneous or homogeneous. When hydrogenation of an alkene generates a chiral center, a pair of enantiomeric products is expected to form. However, an enantiomeric excess of one of the products can be facilitated using an enantioselective reaction or an...
01:28Reduction of Benzene to Cyclohexane: Catalytic Hydrogenation
02:36Regioselectivity and Stereochemistry of Hydroboration
Hydroboration proceeds in a concerted fashion with the attack of borane on the π bond, giving a cyclic four-centered transition state. The –BH2 group is bonded to the less substituted carbon and –H to the more substituted carbon. The concerted nature requires the simultaneous addition of –H and –BH2 across the same face of the alkene giving syn...
02:17Regioselectivity of Electrophilic Additions to Alkenes: Markovnikov's Rule
The hydrohalogenation of an unsymmetrical alkene can yield two haloalkane products, depending on which vinylic carbon takes up the halogen. However, one product usually predominates, where hydrogen adds to the vinylic carbon bearing the...
03:08Hydroboration-Oxidation of Alkenes